--- In "Michael Schmidt" <> wrote:
>
> >
> > I guess this says enough:
> >
> > $ whoami
> > root
> > $ lsmod
> > Module Size Used by Tainted: P
> > tsuart7260 1628 0 (unused)
> > tsuart0 8880 0 [tsuart7260]
> > vfat 10140 0 (unused)
> > fat 29608 0 [vfat]
> > $ insmod tsuart-bat3
> > Using /lib/modules/2.4.26-ts11/kernel/drivers/serial/tsuart-bat3.o
> > insmod: init_module: tsuart-bat3: Operation not permitted
> >
> >
> > Any suggestions?
> >
> > wimpunk.
>
> Can you run the following commands and paste the output?
>
> insmod tsuart-bat3 portDebug=255
> dmesg
>
$ insmod tsuart-bat3 portDebug=255
Using /lib/modules/2.4.26-ts11/kernel/drivers/serial/tsuart-bat3.o
insmod: init_module: tsuart-bat3: Operation not permitted
$ dmesg
Linux version 2.4.26-ts11 (gcc version 3.3.4) #22 Tue
Jun 6 12:23:09 MST 2006
CPU: Arm920Tid(wb) revision 0
Machine: ep9301
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 1 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 4 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 5 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 16 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 17 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 18 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
On node 19 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyAM1,115200 root=/dev/mtdblock1
Relocating machine vectors to 0xffff0000
Console: colour dummy device 80x30
Calibrating delay loop... 99.94 BogoMIPS
Memory: 8MB 8MB 8MB 8MB 8MB 8MB 8MB 8MB = 64MB total
Memory: 61020KB available (1208K code, 336K data, 72K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
CPU: Testing write buffer: pass
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch
devfs: boot_options: 0x1
ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ enabled
ttyS02 at 0x89c003e8 (irq = 40) is a 16550A
ttyS03 at 0x89c002e8 (irq = 33) is a 16550A
ttyS04 at 0x89c003a8 (irq = 40) is a 16550A
ttyS05 at 0x89c002a8 (irq = 33) is a 16550A
Real Time Clock Driver v1.10f
ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
Searching for NAND flash...
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB
3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x00000000-0x00004000 : "TS-BOOTROM"
0x00004000-0x01d04000 : "Linux"
0x01d04000-0x02000000 : "RedBoot"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Mounted root (yaffs filesystem).
Mounted devfs on /dev
Freeing init memory: 72K
sdcard0: Technologic Systems SD card controller, address 0x13000000
sdcard0: no SD card option present on this board
TS-UART/7260 detected a TS-7260 board
ttyTS0 at MMIO 0x12400000 (irq = 32) is a TSUART
TS-UART/BAT3 did not detect a TS-BAT3 board
TS-UART/BAT3 did not detect a TS-BAT3 board
TS-UART/BAT3 did not detect a TS-BAT3 board
TS-UART/BAT3 did not detect a TS-BAT3 board
$
Hope it helps...
wimpunk.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|