With the jumper on it comes up in the SPIFLASHBOOT. I have the
follwoing checksums:
TS-SPIFLASHBOOT - built Oct 3 2006
4118fe72efa55f8a811addb8b08eb27f sdcard.o
eb3eb2403be1bb1880e44f11c3542411 linuxrc
d10ec392e3b8c4b37a1c6fe45ec181e6 linuxrc-sdroot
eb3eb2403be1bb1880e44f11c3542411 linuxrc-fastboot
c44d06ef7a04b930704f16be7e8ca503 linuxrc-usbroot
39260fd1abdd6b45192835bd0e24b6e6 linuxrc-nfsroot
dc47ac4c89b59075bbef483bd280b774 linuxrc-mtdroot
when I type in exit and load in the SD to get to the place where I
copied the two files from the web site.
4118fe72efa55f8a811addb8b08eb27f sdcard.o
5b1fcc706f081fe623a058db4c34c6e4 linuxrc2.7400
The sdcard.o is the same, but the linuxrc I replaced is not. I had
copied the linuxrc2.7400 to the spiflashboot, but not there after a
reboot. I also did copy the .7400 into linuxrc. So I would assume
that the updates don't take since the file is gone on the reboot.
The sdcard.o is was probably always the same one. So my question is
what do I need to mount to make sure the right location gets
updated? Is it the flash on the 9441 that needs to get updated?
Thanks.
--- In Eddie Dawydiuk <> wrote:
>
> Hello,
>
> > Okay, if I copy and paste that link in it worked. Loaded the SD
with
> > the image and all looks good. thanks for that.
> >
> > I have another problem. When trying to boot (jumper not set for
> > boot) I get the following:
> >>> TS-SDBOOT - built Oct 17 2006
> >>> Copyright (c) 2006, Technologic Systems
> > .
> > .
> > .
> > It just hangs after that. I found the fix for the 7400 where you
> > replace the sdcard.o and renaming linuxrc2.7400 to linuxrc-sdroot.
> >
> > After doing that I get the same thing. Am I missing something?
> >
> > I am not sure if I am doing it correctly. Not much description
in
> > that readme file. I boot jumper and get the following:
>
> There isn't much to it. You might want to try running md5sum on the
> linuxrc file/kernel on your board and the ones for the TS-7400
SDBOOT to
> ensure you have replaced both files...
>
> --
> Best Regards,
> ________________________________________________________________
> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
>
>
> >>> TS-SPIFLASHBOOT - built Oct 3 2006
> >>> Copyright (c) 2006, Technologic Systems
> > .
> > .
> > .
> > Finished booting in 3.10 seconds
> > Type 'tshelp' for help
> > $
> >
> > I then run insmod -q -f /sdcard.o and then mount the sdcard.
This is
> > so I can get to those two files that need to be updated that I
have
> > placed on the SD card.
> > But since it is the flash, I think I loose what I copy over. How
can
> > I update the 2 files to fix this problem?
> >
> > I followed the directions from this link:
> > ftp://oz.embeddedarm.com/sdboot_7400/
> >
> > Thanks,
> > Walter
> >
> > --- In Eddie Dawydiuk <eddie@> wrote:
> >> Hello,
> >>
> >>> We are using the 7400 and seems the SD has been corrupted. I
> > searched
> >>> this forum and only found about copying an image.
> >>>
> >>> I tried looking here: The procedure is documented here
> >>> http://www.embeddedarm.com/epc/fastboot.htm.
> >>> but page does not seem to exist.
> >>>
> >>> Can some one point me to a document on reloaded the SD as it
> > comes from
> >>> Embeddedarm.
> >> The link seems to be working fine for me. You'll also want to
see
> > the
> >> following thread.
> >>
> >> http://tech.groups.yahoo.com/group/ts-7000/message/6357
> >>
> >> --
> >> Best Regards,
> >> ________________________________________________________________
> >> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
> >> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
> >> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
> >>
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|