By the way, the command $iwconfig wlan0 ap 00:13:10:7A:F2:CA
doesn't work either, although it doesn't return an error.
BTW2, The channel/freq changes every time I call $iwconfig.
--- In "oj199933" <> wrote:
>
> Ok, the new driver module fixed that problem. :) Unfortunately I
> didn't manage to get an internet connection yet. I've turned off all
> security in my wlan router and then executed $iwlist wlan0 scan:
> --------------------------------------------
> Cell 03 - Address: 00:13:10:7A:F2:CA
> ESSID:"W_OMEGA"
> Mode:Master
> Frequency:2.437 GHz (Channel 6)
> Extra:SignalStrength=100%,LinkQuality:28%
> Encryption key:off
> Bit Rates:1 Mb/s; [..] 48 Mb/s
> Extra:bcn_int=100
> ---------------------------------------------------
> $iwconfig:
> ---------------------------------------------------
> wlan0 802.11b/g NIC ESSID:"robot"
> Mode:Managed Frequency=2.432 GHz Access Point:
> Not-Associated
> Bit Rate:1 Mb/s
> Retry:off RTS thr=2432 B Fragment thr:off
> Encryption key:****-****-****-****-****-****-** Security
> mode:open
> Power Management:off
> Link Quality=96/100 Signal level=30/100 Noise level=0/100
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:3769
> Tx excessive retries:4160 Invalid misc:0 Missed beacon:0
> -----------------------------------------------------
> $iwconfig wlan0 ap w_omega:
> -----------------------------------------------------
> Interface wlan0 doesn't support IP addresses
> wlan0 Interface doesn't support IP addresses
> Error for wireless request "Set AP Address" (8B14) :
> invalid argument "w_omega".
> ------------------------------------------------------
>
> How can I specify an access point??
>
>
>
>
>
> --- In Eddie Dawydiuk <eddie@> wrote:
> >
> > Hello,
> >
> > > I've just received my TS-7400 board and now I work my way trough the
> > > manual (linuxarm-guide-rev2.2). Most of the stuff is working fine.
> > > I've already internet access via ethernet and I downloaded the zd.o
> > > module.
> > > I've used insmod to load the module along with the other modules
> > > mentioned in chapter 6.7. So far so good. But the next step;
"ifconfig
> > > wlan0 up" doesn't work (SIOCGIFFLAGS: No such device).
> >
> > The error indicates there is no such network interface. Can you
send me
> > the output of dmesg. The USB wireless devices we sell were recently
> > upgraded to revision B of the Zydas ZD1211 chipset. As a result we
have
> > a new driver available here
> > ftp://oz.embeddedarm.com/wireless/zd1211/r83/ts7400/zdb.o
> >
> > --
> > Best Regards,
> > ______________________________________________________________
> > Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
> > 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
> > Fountain Hills, AZ 85268 | web: www.embeddedARM.com
> >
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|