ts-7000
[Top] [All Lists]

[ts-7000] Re: TS-7400 wireless network set-up

To:
Subject: [ts-7000] Re: TS-7400 wireless network set-up
From: "oj199933" <>
Date: Wed, 16 May 2007 20:03:12 -0000
Ok, the new driver module fixed that problem. :) Unfortunately I
didn't manage to get an internet connection yet. I've turned off all
security in my wlan router and then executed $iwlist wlan0 scan:
--------------------------------------------
Cell 03 - Address: 00:13:10:7A:F2:CA
                    ESSID:"W_OMEGA"
                    Mode:Master
                    Frequency:2.437 GHz (Channel 6)
                    Extra:SignalStrength=100%,LinkQuality:28%
                    Encryption key:off
                    Bit Rates:1 Mb/s; [..] 48 Mb/s
                    Extra:bcn_int=100
---------------------------------------------------
$iwconfig:
---------------------------------------------------
wlan0     802.11b/g NIC  ESSID:"robot"  
          Mode:Managed  Frequency=2.432 GHz  Access Point:
Not-Associated   
          Bit Rate:1 Mb/s   
          Retry:off   RTS thr=2432 B   Fragment thr:off
          Encryption key:****-****-****-****-****-****-**   Security
mode:open
          Power Management:off
          Link Quality=96/100  Signal level=30/100  Noise level=0/100
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:3769
          Tx excessive retries:4160  Invalid misc:0   Missed beacon:0
-----------------------------------------------------
$iwconfig wlan0 ap w_omega:
-----------------------------------------------------
Interface wlan0 doesn't support IP addresses
wlan0     Interface doesn't support IP addresses
Error for wireless request "Set AP Address" (8B14) :
    invalid argument "w_omega".
------------------------------------------------------

How can I specify an access point??



 

--- In  Eddie Dawydiuk <> wrote:
>
> Hello,
> 
> > I've just received my TS-7400 board and now I work my way trough the
> > manual (linuxarm-guide-rev2.2). Most of the stuff is working fine.
> > I've already internet access via ethernet and I downloaded the zd.o
> > module.
> > I've used insmod to load the module along with the other modules
> > mentioned in chapter 6.7. So far so good. But the next step; "ifconfig
> > wlan0 up" doesn't work (SIOCGIFFLAGS: No such device).
> 
> The error indicates there is no such network interface. Can you send me
> the output of dmesg. The USB wireless devices we sell were recently
> upgraded to revision B of the Zydas ZD1211 chipset. As a result we have
> a new driver available here
> ftp://oz.embeddedarm.com/wireless/zd1211/r83/ts7400/zdb.o
> 
> -- 
> Best Regards,
> ______________________________________________________________
>   Eddie Dawydiuk, Technologic Systems | voice:  (480) 837-5200
>   16610 East Laser Drive Suite 10     | fax:    (480) 837-5300
>   Fountain Hills, AZ 85268            | web: www.embeddedARM.com
>




 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU