Julien,
you have been very kind!
Maybe someone else could give a 7250-oriented tip-n-trick
Thanks again,
Marco
--- In "Julien" <> wrote:
>
> Ok Marco, that's the correct way... I don't understand why your
> modifications are not saved (since you read a "IPADDR=192.168.0.51"
> in the file after editing it). The solution could be there : find
why
> you read something different of what you write in this file.
>
> Maybe there is a special link on the TS7250 beetween the network
> configuration files and redboot... I can just tell you that your
way
> of doing things is the same of mine, and it works for me on a TS7200
> :/
>
> Hope someone else will help you.
>
> Julien
>
> --- In "marcolamonato" <marco@> wrote:
> >
> > julien,
> >
> > I entered the system with a telnet connection from my "command
> > prompt" within WinXP, logged in as root with no password and
> edited
> > the /etc/sysconfig/ifcfg-eth0 with vi.
> > Saved end moved out with ":wq"
> >
> > I could have done it also from a serial connection, but I prefer
> this
> > interface compared to the hyperterminal in WinXP
> >
> > Marco
> >
> >
> >
> >
> > --- In "Julien" <kaezar1@> wrote:
> > >
> > > Just another question Marco : how did you change the IP address
> > from
> > > your telnet connection ? What have you done ?
> > >
> > > Thank you.
> > >
> > > --- In "marcolamonato" <marco@> wrote:
> > > >
> > > > Julien,
> > > >
> > > > I changed the IP address from a telnet connection and I
> > put "down"
> > > > and "up" the network with the ifconfig command as you
> suggested.
> > > >
> > > > Then, from a serial connection I grabbed these information:
> > > >
> > > > $ cat /etc/sysconfig/ifcfg-eth0
> > > > DEVICE=eth0
> > > > IPADDR=192.168.0.51
> > > > NETMASK=255.255.255.0
> > > > NETWORK=192.168.0.0
> > > > BROADCAST=192.168.0.255
> > > > BOOTPROTO=static
> > > > #BOOTPROTO=dhcp
> > > > ENABLE=yes
> > > >
> > > > $ ifconfig
> > > > eth0 Link encap:Ethernet HWaddr 00:D0:69:40:9D:6D
> > > > inet addr:192.168.0.50 Bcast:192.168.0.255
> > > > Mask:255.255.255.0
> > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > > > RX packets:53 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:35 errors:0 dropped:0 overruns:0
carrier:0
> > > > collisions:0 txqueuelen:1000
> > > > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> > > > Interrupt:39
> > > >
> > > > lo Link encap:Local Loopback
> > > > inet addr:127.0.0.1 Mask:255.0.0.0
> > > > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> > > > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> > > > collisions:0 txqueuelen:0
> > > > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> > > >
> > > > Therefore, I re-established a telnet connection with the
> > > 192.168.0.50
> > > > address and it was working, I tried with the 192.168.0.51 and
> it
> > > > didn't.
> > > >
> > > > Usually it works when I change on RedBoot too.
> > > >
> > > > Marco
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > --- In "Julien" <kaezar1@> wrote:
> > > > >
> > > > > Hu ? That seems very strange to me. I mean there is no link
> > > > beetween
> > > > > Redboot IP (used with NFS functionality) and Linux IP (used
> > when
> > > > your
> > > > > linux is running).
> > > > >
> > > > > I have NEVER modified the Redboot IP of my TS7200 (it's
> always
> > > the
> > > > > default value : 192.168.0.50 or smg like that), I always
> > changed
> > > > JUST
> > > > > the IP of /etc/sysconfig/ifcfg-eth0 and it works
> > > perfectly...after
> > > > a
> > > > > reboot or a "ifconfig eth0 down" then "ifconfig eth0 up".
> > > > >
> > > > > --- In "marcolamonato" <marco@>
> wrote:
> > > > > >
> > > > > > Julien,
> > > > > >
> > > > > > if I change the IP on linux and I don't on modify it
> Reboot,
> > I
> > > > > can't
> > > > > > get the new address, I mean I keep connecting on the
older
> IP
> > > > (with
> > > > > > telnet as example), it doesn't work with the new.
> > > > > > It works only changing both of them
> > > > > >
> > > > > > Marco
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > --- In "Julien" <kaezar1@> wrote:
> > > > > > >
> > > > > > > Hi Marco
> > > > > > >
> > > > > > > Indeed, I would say you don't need to change anything
in
> > > > redboot,
> > > > > > as
> > > > > > > far as your application is running under linux. The
only
> > > > > important
> > > > > > IP
> > > > > > > address in this case is, as you said, the one
> > > > > > in /etc/sysconfig/ifcfg-
> > > > > > > eth0.
> > > > > > >
> > > > > > > The IP address under redboot has to be set for example
> if
> > you
> > > > > want
> > > > > > to
> > > > > > > load a kernel directly by connecting and downloading it
> > from
> > > a
> > > > > > server
> > > > > > > on your network.
> > > > > > >
> > > > > > > Julien
> > > > > > >
> > > > > > > --- In "marcolamonato"
<marco@>
> > > wrote:
> > > > > > > >
> > > > > > > > Hi all,
> > > > > > > >
> > > > > > > > when I need to change the static ip address of my TS-
> 7250
> > I
> > > > > > usually
> > > > > > > > edit the /etc/sysconfig/ifcfg-eth0 and then change
the
> > > > address
> > > > > > also
> > > > > > > > within RedBoot with the fconfig command.
> > > > > > > >
> > > > > > > > Is there a way to change the static ip address from
my
> > > > > > application
> > > > > > > > without moving to Redboot also?
> > > > > > > >
> > > > > > > > Probably I'll need to reboot after editing some
> network
> > > > files,
> > > > > > but
> > > > > > > this
> > > > > > > > would be a small issue, thi big one is not to enter
> > RedBoot.
> > > > > > > >
> > > > > > > > Same thing for changing from static to dhcp?
> > > > > > > >
> > > > > > > > Thanks in advance,
> > > > > > > > Marco
> > > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|