Jim,
the new changes in the ifcfg-etho file work if I reboot the system,
but I can't use the ifup/ifdown commands as they give:
$ ifdown eth0
ifdown: /etc/network/interfaces: No such file or directory
I have no /network/interfaces structure in my TS-7250, should I
create it?
Thanks,
Marco
--- In Jim Jackson <> wrote:
>
>
>
>
> On Thu, 19 Jul 2007, marcolamonato wrote:
>
> > Julien,
> >
> > I changed the IP address from a telnet connection and I put "down"
> > and "up" the network with the ifconfig command as you suggested.
>
> no that won't work. "ifconfig" knows nothing about config files.
> You need to use the "ifdown eth0" and "ifup eth0" commands which
read the
> config files to get the configuration information.
>
>
> >
> > Then, from a serial connection I grabbed these information:
> >
> > $ cat /etc/sysconfig/ifcfg-eth0
> > DEVICE=eth0
> > IPADDR=192.168.0.51
> > NETMASK=255.255.255.0
> > NETWORK=192.168.0.0
> > BROADCAST=192.168.0.255
> > BOOTPROTO=static
> > #BOOTPROTO=dhcp
> > ENABLE=yes
> >
> > $ ifconfig
> > eth0 Link encap:Ethernet HWaddr 00:D0:69:40:9D:6D
> > inet addr:192.168.0.50 Bcast:192.168.0.255
> > Mask:255.255.255.0
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:53 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:1000
> > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> > Interrupt:39
> >
> > lo Link encap:Local Loopback
> > inet addr:127.0.0.1 Mask:255.0.0.0
> > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:0
> > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> >
> > Therefore, I re-established a telnet connection with the
192.168.0.50
> > address and it was working, I tried with the 192.168.0.51 and it
> > didn't.
> >
> > Usually it works when I change on RedBoot too.
> >
> > Marco
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > --- In "Julien" <kaezar1@> wrote:
> > >
> > > Hu ? That seems very strange to me. I mean there is no link
> > beetween
> > > Redboot IP (used with NFS functionality) and Linux IP (used when
> > your
> > > linux is running).
> > >
> > > I have NEVER modified the Redboot IP of my TS7200 (it's always
the
> > > default value : 192.168.0.50 or smg like that), I always changed
> > JUST
> > > the IP of /etc/sysconfig/ifcfg-eth0 and it works
perfectly...after
> > a
> > > reboot or a "ifconfig eth0 down" then "ifconfig eth0 up".
> > >
> > > --- In "marcolamonato" <marco@> wrote:
> > > >
> > > > Julien,
> > > >
> > > > if I change the IP on linux and I don't on modify it Reboot, I
> > > can't
> > > > get the new address, I mean I keep connecting on the older IP
> > (with
> > > > telnet as example), it doesn't work with the new.
> > > > It works only changing both of them
> > > >
> > > > Marco
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > --- In "Julien" <kaezar1@> wrote:
> > > > >
> > > > > Hi Marco
> > > > >
> > > > > Indeed, I would say you don't need to change anything in
> > redboot,
> > > > as
> > > > > far as your application is running under linux. The only
> > > important
> > > > IP
> > > > > address in this case is, as you said, the one
> > > > in /etc/sysconfig/ifcfg-
> > > > > eth0.
> > > > >
> > > > > The IP address under redboot has to be set for example if
you
> > > want
> > > > to
> > > > > load a kernel directly by connecting and downloading it
from a
> > > > server
> > > > > on your network.
> > > > >
> > > > > Julien
> > > > >
> > > > > --- In "marcolamonato" <marco@>
wrote:
> > > > > >
> > > > > > Hi all,
> > > > > >
> > > > > > when I need to change the static ip address of my TS-7250
I
> > > > usually
> > > > > > edit the /etc/sysconfig/ifcfg-eth0 and then change the
> > address
> > > > also
> > > > > > within RedBoot with the fconfig command.
> > > > > >
> > > > > > Is there a way to change the static ip address from my
> > > > application
> > > > > > without moving to Redboot also?
> > > > > >
> > > > > > Probably I'll need to reboot after editing some network
> > files,
> > > > but
> > > > > this
> > > > > > would be a small issue, thi big one is not to enter
RedBoot.
> > > > > >
> > > > > > Same thing for changing from static to dhcp?
> > > > > >
> > > > > > Thanks in advance,
> > > > > > Marco
> > > > > >
> > > > >
> > > >
> > >
> >
> >
> >
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|