ts-7000
[Top] [All Lists]

Re: [ts-7000] Need Help on TS-Serial4 !!

To:
Subject: Re: [ts-7000] Need Help on TS-Serial4 !!
From: "Eddie Dawydiuk" <>
Date: Fri, 22 Sep 2006 08:38:13 -0700 (MST)
Hello,

> Only jumpers 5,6,&7 are connected on our ARM boards.

Sorry for the typo, I meant to say Only IRQs 5,6,&7 are connected on our ARM
boards.

//Eddie


>> ----- Original Message ----
>> From: Eddie Dawydiuk <>
>> To: 
>> Sent: Thursday, September 21, 2006 10:11:09 PM
>> Subject: Re: [ts-7000] Need Help on TS-Serial4 !!
>>
>>                           Hello,
>>
>>>    I change IRQ and the problem is still the same. Data comming out from 
>>> TS-SER4 in very low speed. Is there other settings that has to be changed? 
>>> Pls let me know as soon as possible.
>>
>> In my last email I said your problem sounded like your IRQs were not properly
>> configured. I said this because you said there was a 1 second delay between
>> sending data and actually seeing any data being send. If you are still seeing
>> this behavoir then please answer the following questions.
>>
>> What are your jumper settings? What is the outputs of setserial /dev/tts/n
>> where n is the serial port you are writing to.
>>
>> With regard to your comment about the baud rates not being correct, how are
>> you coming to this conclusion? What baud rate are you expecting and what
>> baud rate are you seeing? Is you program reconfiguring the baud rate?
>>
>> //Eddie
>>
>>> ----- Original Message ----
>>> From: Eddie Dawydiuk < com>
>>> To:  .com
>>> Sent: Saturday, September 16, 2006 3:19:07 AM
>>> Subject: Re: [ts-7000] Need Help on TS-Serial4 !!
>>>
>>>                           Hello,
>>>
>>>> I have a TS-7260 SBC and recently i purchase TS-SER4 PC104 extention 
>>>> board. I wrote several programes using those ports but they are woking in 
>>>> very slow manner, they not working in proper baud rate.
>>>>    When I send some srting via one of those serial ports, the reception 
>>>> occurs after about 1s delay in very slow manner.pls help me on this. I 
>>>> need to acsese  these axtra COM ports
>>>
>>> It sounds like your IRQs are not setup properly. Check your jumper settings
>>> to determine which IRQ the TS-SER4 is using. Then you can use setserial to
>>> ensure the proper IRQs are being used.
>>>
>>> //Eddie
>>>
>>>
>>>
>>>
>>>
>>>
>>
>> --
>>
>>
>>
>>
>>
>>
>
>

-- 


 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 



<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU