Re: [ts-7000] auto boot from sd card without the ts-752 board.

[Jonathan Leslie <>]

definitely work with a 700 ohm resistor between pin 5 and ground.  It didn't work without the resisitor. 

next question, where and what  are the script files that run on debian boot?

 reboot works too:

ts7500:/initrd# shutdown -r 0

Broadcast message from (ttyS0) (Thu Jan  1 00:14:07 1970):

The system is going down for reboot NOW!

INIT: Switching to runlevel: 6

INIT: Sending processes the TERM signal

Stopping web server: apache2 ... waiting ..

Stopping NFS common utilities: statd.

Stopping internet superserver: inetd.

Stopping Avahi mDNS/DNS-SD Daemon: avahi-daemon.

Stopping enhanced syslogd: rsyslogd.

Asking all remaining processes to terminate...done.

All processes ended within 1 seconds....done.

Stopping portmap daemon....

not deconfiguring network interfaces: network devices still mounted. (warning).

Cleaning up ifupdown....

Deactivating swap...done.

Unmounting local filesystems...umount2: Device or resource busy

umount: /dev/root busy - remounted read-only

done.

Will now restart.

>> TS-BOOTROM - built Jul 30 2009 13:41:34

>> Copyright (c) 2009, Technologic Systems

>> Booting from microSD card...

.

.

.

Starting the hotplug events dispatcher: udevd.

Synthesizing the initial hotplug events...done.

Waiting for /dev to be fully populated...done.

Activating swap...done.

Cleaning up ifupdown....

Loading kernel modules...done.

Checking file systems...fsck 1.41.3 (12-Oct-2008)

done.

Setting kernel variables (/etc/sysctl.conf)...done.

Mounting local filesystems...done.

Activating swapfile swap...done.

Setting up networking....

Configuring network interfaces...done.

Starting portmap daemon....

Starting NFS common utilities: statd.

INIT: Entering runlevel: 2

Starting enhanced syslogd: rsyslogd.

Starting system message bus: dbus.

Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.

Starting OpenBSD Secure Shell server: sshd.

Starting NFS common utilities: statd.

Starting internet superserver: inetd.

Starting periodic command scheduler: crond.

Starting web server: apache2.

Debian GNU/Linux 5.0 ts7500 ttyS0

ts7500 login: root

Last login: Thu Jan  1 00:01:40 UTC 1970 on ttyS0

Linux ts7500 2.6.24.4 #10 Tue Oct 13 16:15:47 MST 2009 armv4l

The programs included with the Debian GNU/Linux system are free software;

the exact distribution terms for each program are described in the

individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent

permitted by applicable law.

ts7500:~# dhclient eth0; pump;

Internet Systems Consortium DHCP Client V3.1.1

Copyright 2004-2008 Internet Systems Consortium.

All rights reserved.

For info, please visit http://www.isc.org/sw/dhcp/

Listening on LPF/eth0/00:d0:69:42:40:de

Sending on   LPF/eth0/00:d0:69:42:40:de

Sending on   Socket/fallback

DHCPREQUEST on eth0 to 255.255.255.255 port 67

DHCPACK from 10.0.1.1

bound to 10.0.1.74 -- renewal in 306773 seconds.

ts7500:~#

--- On Thu, 1/17/13, Jonathan Klay - NOAA Federal <> wrote:

From: Jonathan Klay - NOAA Federal <>
Subject: Re: [ts-7000] auto boot from sd card without the ts-752 board.
To:
Date: Thursday, January 17, 2013, 5:26 PM

 

Funny, we just had this problem yesterday - our engineer had a jumper on the new baseboard tying that pin to ground and it just kept rebooting.  Had to connect a console terminal to figure out what was happening.

On Thu, Jan 17, 2013 at 2:21 PM, Jonathan Leslie <m("yahoo.com","jleslie48");" target="_blank" href="/mc/compose?to=">> wrote:

I got it!     I attached pin 5 on the 44 pin connector (the MODE2 pin??) to a 700 ohm resistor, and tied that to ground.   

44-Pin Header

The TS-7500 includes a .1" pin spacing external header for board to board interfacing. The TS-7500 external interfaces uses a total of 44 pins.

    _________________________________________________________________ 
   | 2  4  6  8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44|
 * | 1  3  5  7  9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43|
   \-----------------------------------------------------------------/

Pin table:

3.1 44-Pin Header

Pin#	Name	Function
1	JTAG_DOUT
2	JTAG_TMS	4.7k pull-up
3	JTAG_CLK	2.2k pull-up
4	JTAG_DIN	4.7k pull-up
5	DIO_05	DIO, XUART#0 TX, RS232 RTS on TS-752, 4.7k pull-up
6	DIO_06	DIO, XUART#0 RX, RS232 CTS on TS-752
7	DIO_07	Console TX, DB9 RS232 TXD on TS-752, 4.7k pull-up
8	DIO_08	Console RX, DB9 RS232 RXD on TS-752, 4.7k pull-up
9	DIO_09	DIO or ext_reset#

The DIO registers are described in the #Syscon section. This board has 40 logical DIO registers on the FPGA to remain consistant with the series, but not all of the pins are brought out. DIO 9 by default is an external reset which is pulled high, and when it is set to 0 the board will reboot. You can disable this functionality by clearing bit 4 of 0x76 in the #Syscon.

DIO Number	Location	Alternate Function
5	Pin 5 of the #44 Pin Header	MODE2, XUART 0 TX
6	Pin 6 of the #44 Pin Header	XUART 0 RX
7	Pin 7 of the #44 Pin Header	MODE1

--- On Thu, 1/17/13, Jonathan Leslie <m("yahoo.com","jleslie48");" target="_blank" href="/mc/compose?to=">> wrote:

From: Jonathan Leslie <m("yahoo.com","jleslie48");" target="_blank" href="/mc/compose?to=">>

Subject: Re: [ts-7000] auto boot from sd card without the ts-752 board.
To: m("yahoogroups.com","ts-7000");" target="_blank" href="/mc/compose?to=">

Date: Thursday, January 17, 2013, 4:56 PM

 

I tried that:

"rm linuxrc; ln -sf /linuxrc-sdroot /linuxrc; save" 

*After that you will see this message: Saving initrd to SD card...done 

I ran the above from the busybox prompt but it didn't work. 

--- On Thu, 1/17/13, Jonathan Klay - NOAA Federal <m("noaa.gov","jonathan.klay");" target="_blank" href="/mc/compose?to=">> wrote:

From: Jonathan Klay - NOAA Federal <m("noaa.gov","jonathan.klay");" target="_blank" href="/mc/compose?to=">>
Subject: Re: [ts-7000] auto boot from sd card without the ts-752 board.
To: m("yahoogroups.com","ts-7000");" target="_blank" href="/mc/compose?to=">
Date: Thursday, January 17, 2013, 4:44 PM

 

Let the board boot.

Do an "ls -al" -- you should see a link of linuxrc -> linuxrc-fastboot

you will need to rm linuxrc, and then ln -s linuxrc-sdroot linuxrc

to make a new link for the boot type you want.

All in the manual, I believe.

There are many ways to run your script.  Perhaps put a line in /etc/rc.local to call it.

Jonathan

On Thu, Jan 17, 2013 at 1:19 PM, Jon L <> wrote:

I have the TS-7500 on a hand made breadboard.  Currently to get to busybox, I have to:

1) set up a puTTY session to monitor the UART 0
2) when the busybox finishes booting, I type 'exit'
3) the debian linux boots off of the SD card.

I want on power up to boot directly from the SD card, or at least I want the busybox to automatically type in its own 'exit' on the console so it boots the debian linux everytime.   I then want the debian linux to run my startup_script.sh    starting whatever processes' I want,

can anybody give me step by step instructions?   The manual says I should be able to do this by setting MODE1 or MODE2, and I thought this was achievable by pulling these pins (5, and 7 respectively) to ground, but that does not seem to work.

sincerely,

jleslie






------------------------------------

Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
   
   

<*> To unsubscribe from this group, send an email to:
   

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/

--
Jonathan Klay
System Administrator -- System Manager
PMEL CNSD -- Vents Program

NOAA Using Google Get To Know Google Apps, Learn About UMS

--
Jonathan Klay
System Administrator -- System Manager
PMEL CNSD -- Vents Program

NOAA Using Google Get To Know Google Apps, Learn About UMS

__._,_.___

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe

__,_._,___