Good luck. I've never seen that rolling reboot you describe
with any kind of kernel panic, maybe I am just lucky. That is
why I focussed on the disc particulars in my last post. If you
want my default image, tell me where I can copy a 2GB image
to and it's yours.
On Feb 10, 2011, at 3:22 PM, Don Tucker wrote:
> Thanks, Clark. I was using TS's 2.6.290-ts kernel source, but I'll try
> the mainline 2.6.29 kernel with Matthieu's patchset to see if that
> works
> any better. My main fear in using non-TS stuff is that I will need
> drivers for the PC/104 bus to use COM ports on that for the TS-GSM1
> and
> drivers for the TS-ETH2 as well. Hopefully, those will be in there.
>
> Don
>
> On 2/10/2011 5:15 PM, Clark Dunson wrote:
>>
>> Hi Don. I used the 512mbsd-7400-linux2629-lenny-eabi.dd image,
>> and the first thing I did was transfer that image to a 2GB card and
>> make sure it works with dd & bs=2048. Then I enlarged the fourth
>> partition to fill the card. That gave me: my2GB-linux2629-lenny-
>> eabi.dd,
>> which I used as an image from then on.
>>
>> Then I took the 2.6.29 kernel source from www.kernel.org, and applied
>> Matthieu's patchset to it. Then I used the default configuration for
>> TS-7260
>> as a starting point.
>>
>> You'll have to look into arch/arm/config to see the ones Matthieu
>> added, think
>> it was 'make ts7260_def_config' but I could be off a few letters on
>> spelling the
>> make target.
>>
>> The whole thing is tricky.
>> I use standard a USB card reader.
>>
>> The kernel insertion:
>>
>> dd if=/arch/arm/boot/zImage of=/dev/sde2 bs=2048
>>
>> is safe. But you must make darn sure to unmount the
>> auto-mounted /dev/sde1 /cdv/sde2, and /dev/sd4 BEFORE
>> using dd on these other partitions! Running fsck on them occasionally
>> from the host machine is not a bad idea!
>>
>> I finally resorted to using the make modules_install target in the
>> kernel and directing
>> the build to copy the modules to a neutral location:
>>
>> sudo -E make modules_install INSTALL_MOD_PATH=/home/qf/Desktop/bbb
>>
>> and then
>>
>> sudo cp -r /home/qf/Desktop/bbb/lib/modules/ /media/disk-2/lib/
>>
>> Then each of the three mounted partitions must be manually unmounted,
>> or you
>> are asking for trouble: sudo umount /dev/sde1, etc. (sde4 takes ~30
>> seconds
>> to unmount)
>>
>> Best.
>>
>> On Feb 10, 2011, at 2:45 PM, Don Tucker wrote:
>>
>>> Thanks, Clark. Yes, it is a 2GB SD card, and yes, I do use the
>>> bs=2048
>>> option. I can get the 512mbsd-7400-linux2629-lenny-eabi.dd
>>> <ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7260-linux/binaries/ts-
>>> images/512mbsd-7400-linux2629-lenny-eabi.dd.bz2>
>>> image to boot, but not after rebuilding the kernel. Do you have a
>>> default config file for the TS-7260 with the 2.6.29-ts kernel
>>> that you
>>> can point me toward?
>>>
>>> Don
>>>
>>> On 2/10/2011 3:59 PM, Clark Dunson wrote:
>>>>
>>>> Yes Don,
>>>>
>>>> Are you on a 2GB SD card?
>>>> Be sure you include the bs=2048 option to dd every single time you
>>>> write to a 2GB SD card.
>>>> I have replaced the kernel many times without trouble using dd in
>>>> this
>>>> manner.
>>>> That rolling reboot you describe happens here when I don't do it
>>>> right.
>>>>
>>>> On Feb 10, 2011, at 1:48 PM, Rekcut_Nod wrote:
>>>>
>>>>> Has anyone managed to get this combination running? I tried to get
>>>>> this image
>>>>>
>>>>> ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7260-linux/binaries/ts-
>>>>> images/512mbsd-7400-linux2629-lenny-eabi.dd.bz2
>>>>>
>>>>> to boot with a rebuilt kernel using this source
>>>>>
>>>>> ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7260-linux/sources/
>>>>> tskernel-2.6.29-ts-src.tar.gz
>>>>> <ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7260-li%21%0A%20nux/
>>>>> sources/tskernel-2.6.29-ts-src.tar.gz>
>>>>>
>>>>> and a config file that I used with a 2.6.21-ts kernel, but the the
>>>>> resulting SD card just keeps rebooting after the second '.'
>>>>> following
>>>>> the "TS-BOOT" message.
>>>>>
>>>>> I am only considering doing this because the 2.6.21-ts driver for
>>>>> the
>>>>> TS-ETH2 card (ax88796b) seems to have issues. :(
>>>>>
>>>>> Don
>>>>>
>>>>
>>>>
>>>
>>>
>>> ------------------------------------
>>>
>>> Yahoo! Groups Links
>>>
>>>
>>>
>>
>>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|