Roman
I take a 512M SD card and ..
dd if=512mbsd-7400-linux2629-lenny-eabi.dd of=/dev/sdb
on my Linux PC.
I put this into my TS-7300 with JP2 and JP6 jumpered and boot. It goes to the
"Type 'tshelp' for help" prompt.
I type "exit" and it boots from the SD card.
I have to move S12udev in rcS.d to S03udev to get the ethernet port to come up
properly, and I have to "apt-get install nfs-common" for nfs.
The "load_ts7300" code isn't on this image but gcc is, so I compile all
required code from an nfs mounted disk.
I imagine X support will need to be pulled from an earlier image.
regards
Ian T.
--- In Roman Chertov <> wrote:
>
> I have downloaded this images and DDed to a flash card. It boots to the
> prompt, but I have the same exact problem as before. I cannot type anything
> at the prompt and I cannot get past the fastboot menu. Removing J6 does not
> force the board to bypass the fastboot menu. I am missing something?
>
> Thanks,
>
> Roman
>
>
>
>
> ________________________________
> From: bulkoboy11 <>
> To:
> Sent: Fri, October 30, 2009 11:52:21 AM
> Subject: [ts-7000] Re: 2.6 kernel on ts-7300
>
>
> I don't know how many times, I have to post this.
> "512mbsd-7400- linux2629- lenny-eabi. dd" works on the TS-7300.
> It is found at ...
> ftp://ftp.embeddeda rm.com/ts- arm-sbc/ts- 7400-linux/ binaries/ ts-images/
> It provides a 2.6.29 kernel and a Lenny eabi distribution.
> I don't run X, so I don't know how well it supports X.
>
> Ian T.
>
> --- In .com, "rchertov" <rchertov@ .> wrote:
> >
> > Hello,
> >
> > I have ported 2.6.29-ts onto TS-7300 and actually managed to boot it off
> > the flash card. However, there are still two issues that I am facing.
> > First, 64megs of RAM (128MB total) are ignored.
> >
> > Machine: Technologic Systems TS-72xx SBC
> >
> > NR_BANKS too low, ignoring memory at 0xe0000000
> > NR_BANKS too low, ignoring memory at 0xe1000000
> > NR_BANKS too low, ignoring memory at 0xe2000000
> > NR_BANKS too low, ignoring memory at 0xe3000000
> > NR_BANKS too low, ignoring memory at 0xe4000000
> > NR_BANKS too low, ignoring memory at 0xe5000000
> > NR_BANKS too low, ignoring memory at 0xe6000000
> > NR_BANKS too low, ignoring memory at 0xe7000000
> > Memory policy: ECC disabled, Data cache writeback
> > On node 0 totalpages: 16384
> >
> >
> > Second, I have problems with serial login. I can see the login prompt over
> > serial, but I cannot type anything. When I run 'echo "test" > /dev/ttyAM0'
> > on the board, I see the output on the cu terminal of the host computer. (I
> > can SSH into the board to run the commands). If I type a bunch of
> > characters into the serial terminal and then reboot the board, I will see
> > them appear on the fastboot prompt. It is as if the data is not pulled
> > from the host computer and just sits there in the buffer.
> >
> > I have also tried 2.6.21-ts that TS provides along with their nfs_root
> > debian image. I get the same problem. I also checked that the ttyAM0 is
> > present in /etc/securetty.
> >
> > If I use the default 2.4 image, then everything works fine. Except for the
> > case, when there is a second SD card plugged in. Then I experience the
> > same problem. I am curious if anybody experienced this, and how they
> > solved this.
> >
> > Thanks
> >
>
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|