ts-7000
[Top] [All Lists]

Re: [ts-7000] Re: Mounting USB pendrive

To: <>
Subject: Re: [ts-7000] Re: Mounting USB pendrive
From: "LaksCEO" <>
Date: Tue, 22 Apr 2008 12:56:12 +0530
 
-
From:




Post the output from the board as it boots up. Everything from the
bootloader to a login prompt.

Here is the out put during bootloading upto login and after dmesg command

.

 

>> TS-NANDBOOT, Rev 1.00 - built 10:14:31, Mar 7 2005

>> Copyright (C) 2004, Technologic Systems

 

>> TS-BOOTROM, Rev 1.08 - built 16:18:21, Jun 5 2006

>> Copyright (C) 2006, Technologic Systems

>> TS-7250: Rev E1 CPU, Rev B PLD, 32MB SDRAM, options ( RS485 )

>> TS-5620: detected, battery OK, time ( 11:48:24, Apr 22 2008 )

+Ethernet eth0: MAC address 00:d0:69:40:6c:0a

IP: 192.168.0.50/255.255.255.0, Gateway: 192.168.0.1

Default server: 192.168.0.1

RedBoot(tm) bootstrap and debug environment [ROMRAM]

Non-certified release, version current-TS_5 - built 10:49:48, Jun 19 2006

Platform: TS-7250 Board (ARM920T) Rev A

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

RAM: 0x00000000-0x02000000, [0x00052ab0-0x01ff9000] available

FLASH: 0x60000000 - 0x62000000, 2048 blocks of 0x00004000 bytes each.

== Executing boot script in 0.100 seconds - enter ^C to abort

RedBoot> fis load vmlinux

RedBoot> exec -c "console=ttyAM0,115200 root=/dev/mtdblock1"

Using base address 0x00218000 and length 0x000c0000

Linux version 2.4.26-ts11 (gcc version 3.3.4) #22 Tue Jun 6 12:23:096

CPU: Arm920Tid(wb) revision 0

Machine: ep9301

On node 0 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 1 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 4 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 5 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyAM0,115200 root=/dev/mtdblock1

Console: colour dummy device 80x30

Calibrating delay loop... 99.94 BogoMIPS

Memory: 8MB 8MB 8MB 8MB = 32MB total

Memory: 28624KB available (1208K code, 336K data, 72K init)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

CPU: Testing write buffer: pass

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch

devfs: boot_options: 0x1

ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA

ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA

ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA

pty: 1024 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ enabled

Real Time Clock Driver v1.10f

ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic

RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize

Searching for NAND flash...

NAND device: Manufacturer ID: 0x20, Chip ID: 0x75 (ST Micro NAND 32MiB 3,3V 8-bit)

Scanning device for bad blocks

Using static partition definition

Creating 3 MTD partitions on "NAND 32MiB 3,3V 8-bit":

0x00000000-0x00004000 : "TS-BOOTROM"

0x00004000-0x01d04000 : "Linux"

0x01d04000-0x02000000 : "RedBoot"

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NetWinder Floating Point Emulator V0.97 (double precision)

VFS: Mounted root (yaffs filesystem).

Mounted devfs on /dev

Freeing init memory: 72K

INIT: version 2.85-ts1.01 booting

http://www.embeddedarm.com

email:

devfsd v1.3.25 started for /dev

now mounting /proc

mounting local filesystems (in fstab)

sdcard0: Technologic Systems SD card controller, address 0x13000000

sdcard0: no SD card option present on this board

TS-UART/7260 did not detect a TS-7260 board

setting system clock

Tue Apr 22 11:48:32 UTC 2008

./etc/rc.d/rc.local: 1: !/bin/sh: not found

Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/usbcore.o

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

Using /lib/modules/2.4.26-ts11/kernel/arch/arm/common/pcipool.o

Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci.o

Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci-ep93xx.o

usb-ohci.c: USB OHCI at membase 0xe0020000, IRQ 56

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 3 ports detected

Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/scsi_mod.o

SCSI subsystem driver Revision: 1.00

Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/sd_mod.o

Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/storage/usb-storage.o

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

USB Mass Storage support registered.

Using /lib/modules/2.4.26-ts11/kernel/drivers/video/videodev.o

Linux video capture interface: v1.00

Using /lib/modules/2.4.26-ts11/kernel/drivers/video/spca5xx.o

hub.c: new USB device not_pci-1, assigned address 2

usb.c: USB device 2 (vend/prod 0x46d/0x928) is not claimed by any active driver.

usb.c: registered new driver spca5xx

drivers/usb/spca5xx.c: USB SPCA5XX camera found.Logitech QuickCam Express II(SPCA561A)

drivers/usb/spca5xx.c: [spca5xx_probe:5485] Camera type S561

drivers/usb/spca5xx.c: [spca5xx_getcapability:1767] maxw 352 maxh 288 minw 160 minh 10

drivers/usb/spca5xx.c: spca5xx driver 00.60.00.1 registered

Using /lib/modules/2.4.26-ts11/kernel/drivers/video/fbgen.o

Using /lib/modules/2.4.26-ts11/kernel/drivers/video/fbcon-cfb16.o

Using /lib/modules/2.4.26-ts11/kernel/drivers/video/ts7kvfb.o

TS7KV board was not found or firmware not loaded!

insmod: init_module: ts7kvfb: Operation not permitted

mount: special device /dev/scsi/host0/bus0/target0/lun0/part1 does not exist

INIT: Entering runlevel: 3

hub.c: new USB device not_pci-3, assigned address 3

scsi0 : SCSI emulation for USB Mass Storage devices

Vendor: SanDisk Model: Cruzer Micro Rev: 0.3

Type: Direct-Access ANSI SCSI revision: 02

Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0

SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)

sda: Write Protect is off

Partition check:

/dev/scsi/host0/bus0/target0/lun0:Setting hostname.... p1

Bringing up interface eth0..

Bringing up interface lo..

setting kernel IP routing tables

Starting portmap...

Starting INETD...

Starting telnetd...

Starting apache.../www/apache/bin/apachectl start: httpd started

Technologic Systems TS-LINUX/arm 7.0

ts7200 login: root

login[105]: root login on `ttyAM0'

 

 

BusyBox v1.00-rc2 (2004.08.05-21:44+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.

$ dmesg

Linux version 2.4.26-ts11 (gcc version 3.3.4) #22 Tue Jun 6 12:23:096

CPU: Arm920Tid(wb) revision 0

Machine: ep9301

On node 0 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 1 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 4 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

On node 5 totalpages: 2048

zone(0): 2048 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyAM0,115200 root=/dev/mtdblock1

Relocating machine vectors to 0xffff0000

Console: colour dummy device 80x30

Calibrating delay loop... 99.94 BogoMIPS

Memory: 8MB 8MB 8MB 8MB = 32MB total

Memory: 28624KB available (1208K code, 336K data, 72K init)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

CPU: Testing write buffer: pass

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch

devfs: boot_options: 0x1

ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA

ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA

ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA

pty: 1024 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ enabled

Real Time Clock Driver v1.10f

ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic

RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize

Searching for NAND flash...

NAND device: Manufacturer ID: 0x20, Chip ID: 0x75 (ST Micro NAND 32MiB 3,3V 8-bit)

Scanning device for bad blocks

Using static partition definition

Creating 3 MTD partitions on "NAND 32MiB 3,3V 8-bit":

0x00000000-0x00004000 : "TS-BOOTROM"

0x00004000-0x01d04000 : "Linux"

0x01d04000-0x02000000 : "RedBoot"

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NetWinder Floating Point Emulator V0.97 (double precision)

VFS: Mounted root (yaffs filesystem).

Mounted devfs on /dev

Freeing init memory: 72K

sdcard0: Technologic Systems SD card controller, address 0x13000000

sdcard0: no SD card option present on this board

TS-UART/7260 did not detect a TS-7260 board

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb-ohci.c: USB OHCI at membase 0xe0020000, IRQ 56

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 3 ports detected

SCSI subsystem driver Revision: 1.00

Initializing USB Mass Storage driver...

usb.c: registered new driver usb-storage

USB Mass Storage support registered.

Linux video capture interface: v1.00

hub.c: new USB device not_pci-1, assigned address 2

usb.c: USB device 2 (vend/prod 0x46d/0x928) is not claimed by any active driver.

usb.c: registered new driver spca5xx

drivers/usb/spca5xx.c: USB SPCA5XX camera found.Logitech QuickCam Express II(SPCA561A)

drivers/usb/spca5xx.c: [spca5xx_probe:5485] Camera type S561

drivers/usb/spca5xx.c: [spca5xx_getcapability:1767] maxw 352 maxh 288 minw 160 minh 10

drivers/usb/spca5xx.c: spca5xx driver 00.60.00.1 registered

TS7KV board was not found or firmware not loaded!

hub.c: new USB device not_pci-3, assigned address 3

scsi0 : SCSI emulation for USB Mass Storage devices

Vendor: SanDisk Model: Cruzer Micro Rev: 0.3

Type: Direct-Access ANSI SCSI revision: 02

Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0

SCSI device sda: 1000944 512-byte hdwr sectors (512 MB)

sda: Write Protect is off

Partition check:

/dev/scsi/host0/bus0/target0/lun0: p1

WARNING: USB Mass Storage data integrity not assured

USB Mass Storage device found at 3

$


__._,_.___

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe

__,_._,___
<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU