--- In "Peter Santangeli" <> wrote:
>
>
> OK, now I tried switching to udhcpc for kicks, and I get
> "Operation failed." when it tries to run pump.
>
> This is crazy. Getting a DHCP client running on a linux box shouldn't
> be this hard.
>
> I had this same problem with a TS-7260 board months ago, and it never
> got resolved.
>
> I've tried running against DHCP servers on OpenWRT, default Linksys
> boxes, and our regular Slug based system that dozens of machines
> connect happily to every day.
>
> Mean time between email responses from Technologic seems to be 2 days.
>
> I was honestly about to roll out a prototype product based on the Wifi
> box to at least 100 customers. I'm at the point of going back to the
> drawing board on this though.
>
> Is ANYONE running DHCP on a TS box while running full Debian?
>
> Pete
>
>
> --- In "Peter Santangeli" <peter@> wrote:
> >
> >
> > Unfortunately, no joy. Here's the output I get when I run ifup
> > --verbose eth0
> >
> > Configuring interface eth0=eth0 (inet)
> >
> > run-parts --verbose /etc/network/if-pre-up.d
> >
> > run-parts: executing /etc/network/if-pre-up.d/bridge
> >
> > run-parts: executing /etc/network/if-pre-up.d/wireless-tools
> >
> > run-parts: executing /etc/network/if-pre-up.d/wpasupplicant
> >
> >
> >
> > dhclient3 -pf /var/run/dhclient.eth0.pid -lf
> > /var/run/dhclient.eth0.leases eth0
> > Internet Systems Consortium DHCP Client V3.0.4
> >
> > Copyright 2004-2006 Internet Systems Consortium.
> >
> > All rights reserved.
> >
> > For info, please visit http://www.isc.org/sw/dhcp/
> >
> >
> >
> > Listening on LPF/eth0/00:d0:69:40:e8:e5
> >
> > Sending on LPF/eth0/00:d0:69:40:e8:e5
> >
> > Sending on Socket/fallback
> >
> > receive_packet failed on eth0: Network is down
> >
> > DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
> >
> > send_packet: Message too long
> >
> >
> > --- In "charliem_1216" <charliem_1216@>
wrote:
> > >
> > > --- In "Peter Santangeli" <peter@>
> > > wrote:
> > > >
> > > > I asked this a few months ago, and never really got a response.
> > > I'm
> > > > having a heck of a time getting dhcp running on a ts7400. I'm
> > > running
> > > > from the SD card, and pump seems to be failing with:
> > > >
> > > > DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
> > > > send_packet: Message too long
> > > >
> > > > I've tried using pump, dhcpcd, dhcp3-client, all fail the same
> > > way,
> > > > like it is a driver problem.
> > > >
> > > > Does anyone have dhcp running on a ts board running debian?
> > > >
> > > > Pete
> > > >
> > >
> > > Hi Pete --
> > >
> > > This is usually because your MTU is set too low. What
> > > does 'ifconfig eth0' say? MTU=64 is a common but bad value, and
> > > gives the 'Message too long' message. Try 'ifconfig eth0 MTU 1400'.
> > >
> > > Set your dhcp client config to ignore the MTU returned by the
> > > (presumably crappy) dhcp server. (ie for dhcp3-client, remove
> > > the 'interface-mtu' from /etc/dhcp3/dhclient.conf).
> > >
> > > Or if you can control the MTU value the dhcp server hands out, set
> > > it to something reasonable.
> > >
> > > Regards, ....... Charlie
> > >
> >
>
Pete,
I was using udhcpd on a TS7250 a while back.
I had a EDGE/GPRS phone connected to the TS7250 then once connected
issued dhcp addresss to laptops connected via eth0.
I will go pull my configs and setup to see how I implemented it.
Mow
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|