Hello,
I just receive my ts-7260, with the dev kit, and for what I found on
the linux-arm-guide I have to issu 2 commande to be able to boot from
the USBkey to have a full debian environement.
I try to mount the key to see if they was something on it, and that
look like ok.
the I issue the loadUSBModule.sh and the loadUSB.sh , but no luck,
somme error (rsa key, apache not wokring)
so here is the output, any clue ?
$ loadUSBModules.sh
Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/usbcore.o
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Using /lib/modules/2.4.26-ts11/kernel/arch/arm/common/pcipool.o
Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci.o
Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci-ep93xx.o
usb-ohci.c: USB OHCI at membase 0xe0020000, IRQ 56
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/scsi_mod.o
SCSI subsystem driver Revision: 1.00
Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/sd_mod.o
Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/storage/usb-storage.o
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
$ hub.c: new USB device not_pci-1, assigned address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: SanDisk Model: Cruzer Micro Rev: 0.1
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 501759 512-byte hdwr sectors (257 MB)
sda: Write Protect is off
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1
$ loadUSB.sh
Creating extra device nodes...done.
Started device management daemon v1.3.25 for /dev
Checking root file system...
fsck 1.37 (21-Mar-2005)
e2fsck 1.37 (21-Mar-2005)
/dev/scsi/host0/bus0/target0/lun0/part1 has gone 35872 days without
being checked, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/scsi/host0/bus0/target0/lun0/part1: 15067/62744 files (0.4%
non-contiguous), 216963/250696 blocks
Cleaning up ifupdown...done.
Loading modules: usbcore zd zd1211 - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb.c: registered new driver zd1211
pcipool usb-ohci usb-ohci-ep93xx af_packet
Checking all file systems...
fsck 1.37 (21-Mar-2005)
... done.
Setting up networking...done.
Starting hotplug subsystem: usb isapnp ide scsi.
Setting up IP spoofing protection: rp_filter.
Enabling packet forwarding...done.
Configuring network interfaces...done.
Starting portmap daemon: portmap.
Recovering nvi editor sessions... done.
Starting internet superserver: inetd.
Starting OpenBSD Secure Shell server: sshdCould not load host key:
/etc/ssh/ssh_host_rsa_key
Could not load host key: /etc/ssh/ssh_host_dsa_key
Disabling protocol version 2. Could not load host key
sshd: no hostkeys available -- exiting.
Starting NFS common utilities: statd.
Starting periodic command scheduler: cron.
Starting web server: apache-ssl failed
Press enter for maintenance
(or type Control-D to continue):
thanks in advance,
arno
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|