Hello,
> I fouled up the previous answer. BEFORE I made two partitions, there
> was only one. Splitting it had nothing to do with the size. It was
> under 1 gig before I partitioned it and after I partitioned it.
>
> I can't do what you ask, I don't know how. If you could tell me how
> to format it when fdisk only reports that there is 1 gig. The only
> tool I know is fdisk. Is there another tool to low level format it
> (where I can specify the head/cylinder/sector counts?)
I see the failure condition is fdisk reports the card is only 1GB
although it is a 2GB card. You can verify that the sdcard driver on the
initial ramdisk(2nd partition) has the following md5sum.
80cc7284dd647fa67378720655a254d9 sdcard.o
If it does please contact me off list, I'll get you an RMA so we can
look into the issue further...
--
Best Regards,
______________________________________________________________
Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
16610 East Laser Drive Suite 10 | fax: (480) 837-5300
Fountain Hills, AZ 85268 | web: www.embeddedARM.com
> --- In Eddie Dawydiuk <> wrote:
>>
>> Hello,
>>
>>> Only one partition. fdisk only recogized 1 gig. I bought an SD with
>>> pre-installed OS on it from TS (invoice #34396, in case someone needs
>>> to look it up and see if there was an error). Perhaps they sent an
>>> older version of Linux without the correct driver installed. I put a
>>> 2G in the second slot, made two partitions from the available space
>>> and mounted them.
>>
>> Could you provide some information showing the problem of only 1GB being
>> recognized. Could you format the card with a single 2GB partition. Then
>> reboot, then mount the card. Could you then provide the output of dmesg
>> and df.
>>
>> --
>> Best Regards,
>> ______________________________________________________________
>> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
>> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
>> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
>>
>>> --- In Eddie Dawydiuk <eddie@> wrote:
>>>>
>>>> Hello,
>>>>
>>>>> I have a 7300 purchased March 7th. I have a 2G SD in it but
> only 1 is
>>>>> recognized. Could there be an error in my shipment or is this
>>>>> information wrong?
>>>>
>>>> You may want to check the partition table to ensure there aren't
>>>> multiple partitions... What does fdisk say? How are you mounting the
>>>> card? How are you determining you have only 1GB?
>>>>
>>>> --
>>>> Best Regards,
>>>> ______________________________________________________________
>>>> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
>>>> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
>>>> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
>>>>
>>>>
>>>>> --- In Eddie Dawydiuk <eddie@> wrote:
>>>>>>
>>>>>> Hello,
>>>>>>
>>>>>>> I have not had a chance to really explore it, but when I boot to
>>>>> the SD card
>>>>>>> with the new driver, fsck runs saying that it has been quite
>>>>> awhile since
>>>>>>> the partition was checked last. I haven't got a board handy to
>>>>> look at right
>>>>>>> now, so I can't give you the exact details. I was going to look at
>>>>> one of
>>>>>>> the original sd cards to see if it did the same thing as well, but
>>>>> I haven't
>>>>>>> had a chance. What I did notice though was that if I did a
>>>>>>>
>>>>>>> tune2fs -l
>>>>>>>
>>>>>>> the Last checked date was sometime in 1969.
>>>>>>
>>>>>> If you don't have an RTC installed I would expect to see this
>>> behavior.
>>>>>> If this is the case you can use tune2fs to disable the periodic
>>>>>> filesystem check on the card.
>>>>>>
>>>>>> --
>>>>>> Best Regards,
>>>>>> ______________________________________________________________
>>>>>> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
>>>>>> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
>>>>>> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
>>>>>>
>>>>>>> On 4/30/07, Eddie Dawydiuk <eddie@> wrote:
>>>>>>>>
>>>>>>>> Hello,
>>>>>>>>
>>>>>>>>> We are purchasing 7 TS-7300's. There previously was an issue
>>>>> about the
>>>>>>>>> driver for the SD cards not being able to format greater than a
>>>>> 1GIG CF
>>>>>>>>> card. I understand it's been corrected.
>>>>>>>>
>>>>>>>> Yes, since 02/01/2007 the new SD driver that supports up to 4GB
>>>>> SD cards
>>>>>>>> has been shipping.
>>>>>>>>
>>>>>>>> ftp://oz.embeddedarm.com/images/debian/Changelog-Sarge
>>>>>>>>
>>>>>>>>> Will the new units ship with the corrected driver?
>>>>>>>>
>>>>>>>> Yes.
>>>>>>>>
>>>>>>>> --
>>>>>>>> Best Regards,
>>>>>>>> __________________________________________________________
>>>>>>>> Eddie Dawydiuk, Technologic Systems | voice: (480) 837-5200
>>>>>>>> 16610 East Laser Drive Suite 10 | fax: (480) 837-5300
>>>>>>>> Fountain Hills, AZ 85268 | web: www.embeddedARM.com
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Yahoo! Groups Links
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>
>>>
>>>
>>>
>>>
>>> Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>>
>>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|