Hi again, you should probably have usbcore, usb-ohci and usb-storage
(and maybe usb-ohci-ep93xx) modules loaded before anything happens.
When i do lsmod i get:
-----------------------------------------------------
> lsmod
Module Size Used by Not tainted
sd_mod 11100 0 (unused)
scsi_mod 53708 1 [sd_mod]
usb-ohci-ep93xx 892 0 (unused)
usb-ohci 15532 0 [usb-ohci-ep93xx]
pcipool 2080 1 [usb-ohci-ep93xx usb-ohci]
usbcore 55896 1 [usb-ohci]
af_packet 9456 0
-----------------------------------------------------
I have the following content of my "/etc/modules" file:
af_packet
usbcore
pcipool
usb-ohci
usb-ohci-ep93xx
scsi_mod
sd_mod
usb-storage
/Per Ãberg
TuÄrul GÃÃLÃ wrote:
> Hi
>
> I tried dmesg and cat /proc/partitions but neither of them is aware of USB.
>
> Is there any hotplug dameon that I have to install ?
>
> Thanks
>
>
>
> ------------------------------------------------------------------------
>
> *From:* *On
> Behalf Of *Per Ãberg
> *Sent:* Tuesday, March 13, 2007 3:39 PM
> *To:*
> *Subject:* Re: [ts-7000] ts 7400 USB initialization problem
>
>
>
> Hi, have you tried the command "dmesg"?
> dmesg should tell you what it's called. Look for example at my log
> below, my disk is called sdb1.
>
> For a list of partitions that the kernel knows about you may use:
> "cat /proc/partitions"
>
> /Per Ãberg
>
> ----------------------------------------------------------
> usb 5-8: new high speed USB device using ehci_hcd and address 5
> usb 5-8: new device found, idVendor=05e3, idProduct=0702
> usb 5-8: new device strings: Mfr=2, Product=3, SerialNumber=4
> usb 5-8: Product: USB Mass Storage Device
> usb 5-8: Manufacturer: Genesyslogic
> usb 5-8: SerialNumber: 001220002778
> usb 5-8: configuration #1 chosen from 1 choice
> Initializing USB Mass Storage driver...
> scsi2 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 5
> usb-storage: waiting for device to settle before scanning
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> Vendor: IC35L120 Model: AVV207-0 Rev: 0811
> Type: Direct-Access ANSI SCSI revision: 00
> SCSI device sdb: 241254720 512-byte hdwr sectors (123522 MB)
> sdb: test WP failed, assume Write Enabled
> sdb: assuming drive cache: write through
> SCSI device sdb: 241254720 512-byte hdwr sectors (123522 MB)
> sdb: test WP failed, assume Write Enabled
> sdb: assuming drive cache: write through
> sdb: sdb1
> sd 2:0:0:0: Attached scsi disk sdb
> sd 2:0:0:0: Attached scsi generic sg1 type 0
> usb-storage: device scan complete
> ----------------------------------------------------------
>
> TuÄrul GÃÃLÃ wrote:
>> Hi All
>>
>>
>>
>> I have connected USB disk to TS7400 board but couldnât see anything in
>> /dev/sda1 or anything else
>>
>> Where can i locate USB?
>>
>> Thanks
>>
>>
>>
>> ----------------------------------------------------------
>>
>
> --
> Per Ãberg, Ph.D. Student
> Address: Division of Vehicular Systems
> Department of Electrical Engineering
> LinkÃpings universitet
> 581 83 LinkÃping, SWEDEN
> Phone: +46 (0)13-28 23 69
> e-mail: <oberg%40isy.liu.se>
>
>
--
Per Ãberg, Ph.D. Student
Address: Division of Vehicular Systems
Department of Electrical Engineering
LinkÃpings universitet
581 83 LinkÃping, SWEDEN
Phone: +46 (0)13-28 23 69
e-mail:
------------------------ Yahoo! Groups Sponsor --------------------~-->
Yahoo! Groups gets a make over. See the new email design.
http://us.click.yahoo.com/hOt0.A/lOaOAA/yQLSAA/CFFolB/TM
--------------------------------------------------------------------~->
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|