ts-7000
[Top] [All Lists]

[ts-7000] Re: TS-7250 failure to see bootloader messages

To:
Subject: [ts-7000] Re: TS-7250 failure to see bootloader messages
From: "prak75_2004" <>
Date: Wed, 14 Feb 2007 23:11:08 -0000
Hi,

I have tested using a loopback test as described in
http://www.lammertbies.nl/comm/cable/RS-232.html, and I was able to
communicate without connecting to TS-7250.

Regards,

Stanley Lee

--- In  "Jesse" <> wrote:
>
> Okay, I picked up two things from your last message,
> the board has been communicating successfully until recently,
> and that you checked your usb-to-serial converter with a 
> feedback test. Was the feedback test what i call a loopback
> connection between tx and rx, pins 2 & 3?  Can you do this
> test at the TS-7250 Com1 end, that is short pin 2 to 3, and
> see if you can communicate without being connected to the
> TS-7250?  If indeed you can communicate, then I believe the
> problem is in the TS-7250 itself, something must have changed
> there.
> 
> //Tech77man
> 
> 
> --- In  "prak75_2004" <stanigator@> wrote:
> >
> > Hi,
> > 
> > I have connected in such manner (null modem adapter, gender 
> changer,
> > usb-to-serial adapter) and was able to communicate with my TS-7250
> > board properly until quite recently. The gender changer is used b/c
> > the gender of my usb-to-serial adapter and the output of the null
> > modem adapter don't match each other.
> > 
> > Sincerely,
> > 
> > Stanley Lee
> > 
> > --- In  Jim Jackson <jj@> wrote:
> > >
> > > 
> > > 
> > > 
> > > On Tue, 13 Feb 2007, prak75_2004 wrote:
> > > 
> > > > Hi Tech77man,
> > > >
> > > > I have connected COM1 of the TS-7250 board to my laptop using 
> a null
> > > > modem adapter, followed by a gender changer,
> > > 
> > > This is ringing alarm bells - you shouldn't need a gender changer
> > > if the null-modem cable really is a null-modem cable!
> > > 
> > > I suspect you have an ordinary modem cable - with straight thru' 
> pin
> > > connections. A Null-Modem cable is a Special cable with pin 
> connections
> > > Crossed, as people have mentioned here.
> > > 
> > > 
> > > > and usb-to-serial
> > > > connector to my laptop to the correct COM port.
> > > > The settings of Hyperterminal is set to operate at a baud rate 
> of
> > > > 115200, with 8N1 and None for Flow control on the correct COM 
> port, as
> > > > instructed in the manual.
> > > >
> > > > Regards,
> > > >
> > > > Stanley Lee
> > > >
> > > > --- In  "Jesse" <jessenewton@> wrote:
> > > > >
> > > > > Okay, the only things I see that you have not clarified in 
> your
> > > > > message is the type of cable (1) it should be a null modem
> > > > > cable to Com1 connector, which means that the hardware 
> control
> > > > > signals are connected to each other at pins 4 to 6 and 7 to 
> 8,
> > > > > by doing so, tx and rx are enabled and not blocked. (2) is 
> the
> > > > > settings of Hyperterm, it should be set to whatever Com port
> > > > > that you are physically connected to, with 8N1 and None for
> > > > > Flow control. If all of that is in place, a power-up on the
> > > > > TS-7250 board, or pushing the reset button, should allow you
> > > > > to see the bootup messages.
> > > > >
> > > > > //Tech77man
> > > > >
> > > > > --- In  "prak75_2004" <stanigator@> 
> wrote:
> > > > > >
> > > > > > Hi,
> > > > > >
> > > > > > I have trouble seeing redboot messages of my TS-7250 
> board. I have
> > > > > > jumpers 2 and 3 connected, and the power lights are on. I 
> have
> > > > > trouble
> > > > > > communicating between the host computer and the 
> microcontroller
> > > > > using
> > > > > > Hyperterminal in Windows through using a usb-to-serial 
> converter.
> > > > > > We've checked the usb-to-serial converter using the 
> feedback test,
> > > > > and
> > > > > > we've made sure that the transmit/receive pins at the
> > > > > microcontroller
> > > > > > and the usb-to-serial cable end are connected properly. 
> I'm not
> > > > > sure
> > > > > > what else to check to see whether the board is working or 
> not. Can
> > > > > > someone give me some suggestions?
> > > > > >
> > > > > > Thanks,
> > > > > >
> > > > > > Stanley Lee
> > > > > >
> > > > >
> > > >
> > > >
> > > >
> > >
> >
>




 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU