Sockets support many types of protocols other than tcp (Appletalk, for example)
One of these protocols that is supported in most stacks is "raw" Ethernet, or
no protocol at all. You get everything that comes in on the interface
--------------------------------------------
On Tue, 11/5/13, Jonathan Leslie <> wrote:
Subject: Re: [ts-7000] ts-7800 how do I make 4 (at least 2) identical network
stacks?
To: "" <>
Date: Tuesday, November 5, 2013, 3:51 PM
when you say raw
ethernet are you talking sockets connections or something
more "raw" than that?
From: Walter Marvin
<>
To:
Sent:
Tuesday, November 5, 2013 10:22 AM
Subject: Re:
[ts-7000] ts-7800 how do I make 4 (at least 2) identical
network stacks?
The same effect, however, can be done using raw
Ethernet on the receiving side
--------------------------------------------
On Mon, 11/4/13, Eric Robishaw <>
wrote:
Subject: Re: [ts-7000] ts-7800 how do I make 4 (at least 2)
identical network stacks?
To: ""
<>
Date: Monday, November 4, 2013, 9:08 PM
Maybe this is too simple... But why not just use
Udp broadcasting, let each device receive all the
messages
and filter out what they don't need. No need
for
special routing, etc..
On Monday, November 4, 2013, Walter Marvin wrote:
The mac address can be easily found. The problem
here is that Linux won't accept the same sub network
on
two different interfaces and the IPs of the remote boxes
can't be changed. This has to be handled by routing
below the interface level, or raw Ethernet.
--------------------------------------------
On Mon, 11/4/13, Joseph Bouchard <>
wrote:
Subject: Re: [ts-7000] RE: ts-7800 how do I make 4 (at
least
2) identical network stacks?
To:
Date: Monday, November 4, 2013, 5:39 PM
Hi,
I've been following along in the background,
reading
about half of
what's been said, and understanding less, but I
haven't seen anyone
suggest this...
Can you use ARP to an advantage here? The normal way
I've used ARP is
when we have a terminal server which has not yet been
configured... you
arp the mac address to a hostname on your PC, then
connect
to the still
unconfigured box, and configure it. Your computer
knows
how
to find
that remote box by it's mac address, even if the
remote
box doesn't yet
know what it's IP address is yet. Can we do that
here?
Imagine this implementation... You have 4 boxes which
all
want to have
the same IP address, but they all have different MAC
addresses, which
I'll refer to MAC1, MAC2, etc. On your TS7800 you
have
a plain old
single interface eth0 with the address of your choice,
and
a
typical
socket listener. When a client connects, you accept(),
like
you
normally would. It's been years since I've
dealt
with the addr structs
the sockets use, but I'm thinking there is a way to
tie
a mac address to
the socket, or lacking that use arp. At that point
your
file descriptor
is working correctly and you don't care about IP
addresses, you are just
talking back and forth op that open socket.
Maybe I've missed some critical detail, but the
point
is
when you use
mac addresses, and/or hostnames, and you don't
worry
about addresses any
more.
Good luck,
Joe
------------------------------------
Yahoo Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo Groups is subject to:
http://info.yahoo.com/legal/us/yahoo/utos/terms/
|