|
The SD card comes with the ts7260 board. Ricardo De: Don Tucker <> Para: Enviado: martes, 31 de enero de 2012 13:23 Asunto: Re: [ts-7000] Boot debian on sd card Uh oh. That's not a good sign. Where did you get your SD card image? Don On 1/31/2012 10:13 AM, Ricardo Gabriel wrote: > Hi Don! > > I followed your instructions. > > After completing step 15, restart the ts7260board, but the system does not boot. > > Only the following message appears repeatedly: > > > >> TS-SDBOOT - built Aug 10 2009 > >> Copyright (c) 2007, Technologic Systems > > > >> TS-SDBOOT - built Aug 10 2009 > >> Copyright (c) 2007, Technologic Systems > > > >> TS-SDBOOT - built Aug 10 2009 > >> Copyright (c) 2007, Technologic Systems > > Is there any way to recover the boot? > > > Ricardo > > > > ------------------------------------------------------------------------ > *De:* Don Tucker <m("arlut.utexas.edu","dtucker");" href="">> > *Para:* m("yahoogroups.com","ts-7000");" href=""> > *Enviado:* lunes, 30 de enero de 2012 14:14 > *Asunto:* Re: [ts-7000] Boot debian on sd card > > NOTE: The following procedure is IRREVERSIBLE. > > 1.Download the tsbootrom-update from ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7200-linux/binaries/ts-u! tils/tsbootrom-update <ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7200-linux/binaries/ts-utils/tsbootrom-update> and put it onto a USB flash drive. > 2.Boot into a stock TS-7260 using the development interface. Type 'root' to log in. > 3.run /usr/bin/loadUSBModules.sh > 4.Plug in the USB flash drive and you will see a message indicating where it is mounted (e.g. /dev/scsi/host0/bus0/target0/lun0/part1 ). > 5.Type mount /dev/scsi/host0/bus0/target0/lun0/part1 /mnt . This will mount the device at /mnt . > 6.Copy tsbootrom-update from the /mnt directory over onto the /root directory. > 7.Return to /root and type umount /dev/scsi/host0/bus0/target0/lun0/part1 to unmount the device. THIS MUST BE DONE or you risk corrupting the file system (if there is one) on the USB device upon power down or removal. > 8.Type mac=`ifconfig eth0 | grep HWaddr | cut -d' ' -f11` > 9.Then type tsbootrom-update -s -m $mac NOTE: If this is not done you will lose your MAC address forever. > 10.Place the SD card into the TS-7260 SD card slot and reboot the TS-7260. > 11.You should boot into the fastboot shell after a few seconds. From within the shell, type the following: > 12.ln -sf /linuxrc-sdroot /linuxrc > 13.sync > 14.save > 15.reboot This should boot the TS7260 to a login prompt on the Debian file system of the SD card. You may have to try creating this link a few times before it actually saves. > 16.See this link (http://www.embeddedarm.com/software/arm-linux-fastboot-ts7300.php) for more information. > > Don > On 1/30/2012 11:02 AM, ricardogabriel5 wrote: > > > > Hi! > > > > I have a TS7260 board and sd card with debian linux. > > > > The sd card has 3 partitions: > > > > The second and thrid partitions have files. But the first partition is empty with an unknown format > > > > What steps should I follow to make the board boot from sd card? > > > > Regards, > > > > Ricardo > > > > > > > > __._,_.___
Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required) Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe __,_._,___ |