The TS-GSM1 manual indicates that JP1 ON, JP2 OFF, JP3 OFF will use COM2
(ttyS1), with io=0x2f8. If you want to use ttyS2 and io=3e8, change your
jumpers to JP1 OFF, JP2 ON, JP3 OFF.
Don
On 5/16/2011 2:08 PM, thep_in wrote:
I have read a lot of mailing list here and I still got the problem.
I'm using TS-7800 with Linux ts7800 2.6.34 #4 PREEMPT Tue Oct 26
16:23:25 PDT 2010 armv5tel GNU/Linux ,the image I downloaded from
http://goo.gl/nqE1H
I connect them on pc104, setting jumper on pin1,4,5 with irq6 (as I
read here (exp:http://goo.gl/uwDOY ))
when it starts, I followed this step
* . /initrd/ts7800.subr
* pc104on
o The TS-GSM1's LED turned ON
* peekpoke 8 0xEE000198
o the result is 0xFF but the LED start blinking as the
manual says
* modprobe ts7800_isa16550 irq=6 io=0x3e8
o I don't know what this command is, just followed
* dmesg
o result is ...
Linux version 2.6.34 (gcc version 4.4.!
1 (Sourcery G++ Lite 2010q1-202) ) #4 PREEMPT Tue Oct 26 16:23:25
PDT 2010
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=b0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Technologic Systems TS-78xx SBC
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c03d14a0, node_mem_map c03f1000
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
Calling iotable_init(), orion5x_io_desc[0].pfn = 0x000F1000,
orion5x_io_desc[0].virtual = 0xFDD00000,
orion5x_io_desc[0].length = 1048576
BUG: mapping for 0xee000000 at 0xee000000 overlaps vmalloc space
Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 32512
Kernel command line: root=/dev/ram0 rw lpj=1662976
console=null init=/linuxrc
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 121820k/121820k available, 9252k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0025000 ( 116 kB)
.text : 0xc0025000 - 0xc0376000 (3396 kB)
.data : 0xc03b6000 - 0xc03d1ac0 ( 111 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:96
Console: colour dummy device 80x30
Calibrating delay loop (skipped) preset value.. 332.59
BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
TS-78xx FPGA: magic=0x00b480, rev=0x05
TS-78xx: RTC not registered
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
TS-7800 DMA controller init.
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 32
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive);
looks like an initrd
Freeing initrd memory: 4096K
NetWinder Floating Point Emulator V0.97 (double precision)
JFS: nTxBlock = 983, nTxLock = 7869
yaffs built Oct 26 2010 16:19:14 Installing.
msgmni has been set to 245
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:69:42:0b:41
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: not present
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Warning: unable to open an initial console.
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1536KiB [1 disk] into ram disk... done.
EXT2-fs (ram0): warning: mounting unchecked fs, running e2fsck
is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
devtmpfs: mounted
Freeing init memory: 116K
tssdcard: Technologic Systems SD card controller, address
0xe8000100
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus
number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
orion-ehci orion-ehci.1: Marvell Orion EHCI
orion-ehci orion-ehci.1: new USB bus registered, assigned bus
number 2
orion-ehci orion-ehci.1: irq 12, io mem 0xf10a0000
orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb 1-1: new high speed USB device using orion-ehci and address 2
usb 2-1: new high speed USB device using orion-ehci and address 2
tssdcard: no card found.
tssdcard: Technologic Systems SD card controller, address
0xe8000100
tssdcard: card /dev/tssdcardb has 3962880 sectors (LUN 1)
tssdcardb: tssdcardb1 tssdcardb2 tssdcardb3 tssdcardb4
EXT2-fs (tssdcardb4): error: ext2_lookup: deleted inode
referenced: 4195
Initializing USB Mass Storage driver...
scsi0 : usb-storage 2-1:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 0:0:0:0: Direct-Access Kingston DT101 II 8.20 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7825408 512-byte logical blocks: (4.00
GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
udev: renamed network interface eth0 to eth1
libata version 3.00 loaded.
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi1 : sata_mv
scsi2 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
EXT2-fs (tssdcardb4): error: ext2_lookup: deleted inode
referenced: 4195
EXT2-fs (tssdcardb4): warning: mounting unchecked fs, running
e2fsck is recommended
EXT2-fs (tssdcardb4): error: ext2_lookup: deleted inode
referenced: 4195
EXT2-fs (tssdcardb4): error: ext2_lookup: deleted inode
referenced: 4195
eth1: link up, 100 Mb/s, full duplex, flow control disabled
* cat < /dev/ttyS2 &
o [1] 1661
o Input/output error
o [1]+ Exit 1
What should do next?
smime.p7s
Description: S/MIME Cryptographic Signature
|