I haven't used those routines, but I HAVE used other routines that are
also included among the ts7xxx.subr shell functions (i.e. led0 and led1)
and they both worked. You just have to make sure you launch the
ts7xxx.subr shell first.
Don
On 2/11/2011 11:04 AM, wrote:
>
> I'm talking about running the following commands that come with the
> ts-7260:
>
> dio_dir_get <n>: get the current direction (0=input,1=output) of DIO
> #n (n in 0..15)
> dio_dir_set <n> <dir>: set the direction of DIO #n to the specified
> direction
> (0=input,1=output)
> dio_data_get <n>: get the current value (0=Low,1=High) of DIO #n
> dio_data_set <n> <val>: set the current value
>
> have any of you used these scripts/commands sucessfully out of the
> box? I need to know if they work before purcashing the ts-7260,
> because i purchased a ts-4200/ts-8100 and the scripts on the board do
> not work.
>
> Claudio
>
> --- In <ts-7000%40yahoogroups.com>,
> "Clark" <> wrote:
> >
> > Answer: This code does work on my system.
> >
> > --- In <ts-7000%40yahoogroups.com>,
> "Clark" <cdunson@> wrote:
> > >
> > > Let's see if we can't focus this discussion a little better. Is
> this the same deal I face attempting to access GPIO? Joel said I need
> to use a read-modify-write instruction, yet the TS sample code
> 'button.c' shows the naive approach of using simple assignment in C.
> Thus the question to me is does this sample code work? Why not?
> > >
> > > / filename button.c
> > > // connect a button to DIO pin 1 and ground
> > > // blinks green and red led on the ts-7200 when button is pressed
> > > //
> > > // compile arm-linux-gcc -o button button.c
> > > //
> > >
> > > #include<unistd.h>
> > > #include<sys/types.h>
> > > #include<sys/mman.h>
> > > #include<stdio.h>
> > > #include<fcntl.h>
> > > #include<string.h>
> > >
> > > int main(int argc, char **argv)
> > > {
> > > volatile unsigned int *PEDR, *PEDDR, *PBDR, *PBDDR, *GPIOBDB;
> > > int i;
> > > unsigned char state;
> > > unsigned char *start;
> > > int fd = open("/dev/mem", O_RDWR|O_SYNC);
> > >
> > > start = mmap(0, getpagesize(), PROT_READ|PROT_WRITE, MAP_SHARED,
> fd, 0x80840000);
> > > PBDR = (unsigned int *)(start + 0x04); // port b
> > > PBDDR = (unsigned int *)(start + 0x14); // port b direction register
> > > PEDR = (unsigned int *)(start + 0x20); // port e data
> > > PEDDR = (unsigned int *)(start + 0x24); // port e direction register
> > > GPIOBDB = (unsigned int *)(start + 0xC4); // debounce on port b
> > >
> > > *PBDDR = 0xf0; // upper nibble output, lower nibble input
> > > *PEDDR = 0xff; // all output (just 2 bits)
> > > *GPIOBDB = 0x01; // enable debounce on bit 0
> > >
> > > state = *PBDR; // read initial state
> > > while (state & 0x01) { // wait until button goes low
> > > state = *PBDR; // remember bit 0 is pulled up with 4.7k ohm
> > > }
> > >
> > >
> > > // blink 5 times, sleep 1 second so it's visible
> > > for (i = 0; i < 5; i++) {
> > > *PEDR = 0xff;
> > > sleep(1);
> > > *PEDR = 0x00;
> > > sleep(1);
> > > }
> > > close(fd);
> > > return 0;
> > > }
> > >
> > >
> > > --- In <ts-7000%40yahoogroups.com>,
> dalibor@ wrote:
> > > >
> > > > > can someone confirm the DIO pins work on the ts-7260 using the
> provided
> > > > > scripts ?
> > > > >
> > > > >
> > > >
> > > > Hello,
> > > > probably the same problem,
> > > >
> > > > I am not able to control DIO pins from user space. Tried C code via
> > > > registers, peekpoke, GPIO kernel modules, but nothing worked.
> The pins are
> > > > still high (log 1). LED connected to the pin is still lighting.
> > > >
> > > > The only thing I managed is to read the pins, when I connect it
> to ground,
> > > > I can read log 0, log 1 when disconnected.
> > > >
> > > > Thanks in advance for any tips..
> > > >
> > > > Dalibor
> > > >
> > >
> >
>
>
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|