Ok, never mind about the initrd problem - I was missing CONFIG_BLK_DEV_RAM. Now
I get to the fasboot prompt but then I think the watchdog expires.
I'll try to get that rectified next. I thought I added the watchdog patch but
maybe it didn't get built into the kernel right...
Andrew
--- In "andreas queisser" <> wrote:
>
>
> Hi Ian,
>
> What do the patch-patches do? I'm using the matt-2 patches against the
> .34 kernel.
>
> Could you send me your .config for the .34 kernel?
> <> ). I notice that in your printout you have
> the lines
>
> Trying to unpack rootfs image as initramfs...
> rootfs image is not initramfs (junk in compressed archive); looks like
> an initrd
> Freeing initrd memory: 4096K
>
> where I have
>
> Unpacking initramfs...
> Initramfs unpacking failed: junk in compressed archive
> Freeing initrd memory: 4096K
>
> Maybe my options for the initrd/ram disk are wrong.
>
> How did you create your initrd image on the third partition of the SD
> card? I'm using the one from the lenny SD image from the TS site. That
> could be wrong as well.
>
> Thanks,
>
> Andrew
>
> --- In Ian Thompson <ian.thompson@> wrote:
> >
> > Andrew
> >
> > There are a few "patches to the patches" required. I haven't checked
> > recently to see if they have worked their way back into the system.
> > Below is my boot list.
> >
> > Ian T.
> >
> >
> > >> TS-SDBOOT - built Jul 6 2006
> > >> Copyright (c) 2006, Technologic Systems
> > .
> > .
> > .
> > Uncompressing Linux... done, booting the kernel.
> > Linux version 2.6.34-m1 (gcc version 4.3.2
> (Debian
> > 4.3.2-1 .1) ) #16 PREEMPT Wed Aug 18 08:28:01 MST 2010
> > CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=40007177
> > CPU: VIVT data cache, VIVT instruction cache
> > Machine: Technologic Systems TS-72xx SBC
> > Memory policy: ECC disabled, Data cache writeback
> > Built 1 zonelists in Zone order, mobility grouping on. Total pages:
> 9040
> > Kernel command line: console=ttyAM0,115200 root=/dev/ram0 rw
> init=/linuxrc
> > PID hash table entries: 256 (order: -2, 1024 bytes)
> > Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> > Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> > Memory: 8MB 8MB 8MB 8MB 8MB 8MB 8MB 8MB = 64MB total
> > Memory: 57496k/57496k available, 8040k reserved, 0K highmem
> > Virtual kernel memory layout:
> > vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> > fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> > DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
> > vmalloc : 0xce000000 - 0xfe800000 ( 776 MB)
> > lowmem : 0xc0000000 - 0xcd800000 ( 216 MB)
> > modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> > .init : 0xc0008000 - 0xc0022000 ( 104 kB)
> > .text : 0xc0022000 - 0xc02e3000 (2820 kB)
> > .data : 0xc02f8000 - 0xc0317860 ( 127 kB)
> > Hierarchical RCU implementation.
> > NR_IRQS:120
> > VIC @fefb0000: id 0x00041190, vendor 0x41
> > VIC @fefc0000: id 0x00041190, vendor 0x41
> > Console: colour dummy device 80x30
> > Calibrating delay loop... 99.73 BogoMIPS (lpj=498688)
> > Security Framework initialized
> > Mount-cache hash table entries: 512
> > CPU: Testing write buffer coherency: ok
> > NET: Registered protocol family 16
> > ep93xx clock: PLL1 running at 400 MHz, PLL2 at 192 MHz
> > ep93xx clock: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
> > ep93xx dma_m2p: M2P DMA subsystem initialized
> > ep93xx dma_m2m: M2M DMA subsystem initialized
> > bio: create slab <bio-0> at 0
> > SCSI subsystem initialized
> > NET: Registered protocol family 2
> > IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> > TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> > TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
> > TCP: Hash tables configured (established 2048 bind 2048)
> > TCP reno registered
> > UDP hash table entries: 256 (order: 0, 4096 bytes)
> > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> > NET: Registered protocol family 1
> > Trying to unpack rootfs image as initramfs...
> > rootfs image is not initramfs (junk in compressed archive); looks like
> > an initrd
> > Freeing initrd memory: 4096K
> > NetWinder Floating Point Emulator V0.97 (double precision)
> > JFS: nTxBlock = 481, nTxLock = 3849
> > msgmni has been set to 120
> > alg: No test for stdrng (krng)
> > io scheduler noop registered
> > io scheduler deadline registered
> > io scheduler cfq registered (default)
> > Serial: AMBA driver
> > apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
> > console [ttyAM0] enabled
> > apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
> > apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
> > brd: module loaded
> > No NAND device found.
> > ep93xx_mii_bus: probed
> > ep93xx_eth:ep93xx_mii_probe: PHY supports MII frame preamble
> suppression
> > ep93xx_eth:ep93xx_mii_probe: attached PHY driver [Generic PHY]
> > (mii_bus:phy_addr =0:01, irq=-1)
> > net eth0: ep93xx on-chip ethernet, IRQ 39, 00:d0:69:41:51:cb
> > ep93xx-rtc ep93xx-rtc: rtc core: registered ep93xx-rtc as rtc0
> > rtc-m48t86 rtc-m48t86: rtc core: registered m48t86 as rtc1
> > rtc-m48t86 rtc-m48t86: battery ok
> > ts72xx-wdt ts72xx-wdt: TS-72xx Watchdog driver
> > TCP cubic registered
> > NET: Registered protocol family 17
> > rtc-m48t86 rtc-m48t86: setting system clock to 2010-10-12 15:47:26 UTC
> > (12868984 46)
> > RAMDISK: ext2 filesystem found at block 0
> > RAMDISK: Loading 1536KiB [1 disk] into ram disk... done.
> > EXT2-fs (ram0): warning: mounting unchecked fs, running e2fsck is
> > recommended
> > VFS: Mounted root (ext2 filesystem) on device 1:0.
> > Freeing init memory: 104K
> > >> Booting to SD Card...
> > ts72xx-sdcard ts72xx-sdcard.0: SD card hardware revision: 00000000
> > ts72xx-sdcard ts72xx-sdcard.0: block device major number = 254
> > ts72xx-sdcard ts72xx-sdcard.0: New SD card detected, name=tssdcarda
> > size=990976 (sectors)
> > tssdcarda: tssdcarda1 tssdcarda2 tssdcarda3 tssdcarda4
> > jfs: Unrecognized mount option "relatime" or missing value
> > Mount failed for selinuxfs on /selinux: No such file or directory
> > INIT: version 2.86 booting
> >
> >
> > This e-mail, including any attachments and response string, may
> contain proprietary information which is confidential and may be legally
> privileged. It is for the intended recipient only. If you are not the
> intended recipient or transmission error has misdirected this e-mail,
> please notify the author by return e-mail and delete this message and
> any attachment immediately. If you are not the intended recipient you
> must not use, disclose, distribute, forward, copy, print or rely on this
> e-mail in any way except as permitted by the author.
> >
>
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|