Hi Ian,
What do the patch-patches do? I'm using the matt-2 patches against the .34 kernel.
Could you send me your .config for the .34 kernel? I notice that in your printout you have the lines
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks like
an initrd
Freeing initrd memory: 4096K
where I have
Unpacking initramfs...
Initramfs unpacking failed: junk in compressed archive
Freeing initrd memory: 4096K
Maybe my options for the initrd/ram disk are wrong.
How did you create your initrd image on the third partition of the SD card? I'm using the one from the lenny SD image from the TS site. That could be wrong as well.
Thanks,
Andrew
--- In Ian Thompson <> wrote:
>
> Andrew
>
> There are a few "patches to the patches" required. I haven't checked
> recently to see if they have worked their way back into the system.
> Below is my boot list.
>
> Ian T.
>
>
> >> TS-SDBOOT - built Jul 6 2006
> >> Copyright (c) 2006, Technologic Systems
> .
> .
> .
> Uncompressing Linux... done, booting the kernel.
> Linux version 2.6.34-m1 (gcc version 4.3.2 (Debian
> 4.3.2-1 .1) ) #16 PREEMPT Wed Aug 18 08:28:01 MST 2010
> CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=40007177
> CPU: VIVT data cache, VIVT instruction cache
> Machine: Technologic Systems TS-72xx SBC
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9040
> Kernel command line: console=ttyAM0,115200 root=/dev/ram0 rw init=/linuxrc
> PID hash table entries: 256 (order: -2, 1024 bytes)
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Memory: 8MB 8MB 8MB 8MB 8MB 8MB 8MB 8MB = 64MB total
> Memory: 57496k/57496k available, 8040k reserved, 0K highmem
> Virtual kernel memory layout:
> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
> vmalloc : 0xce000000 - 0xfe800000 ( 776 MB)
> lowmem : 0xc0000000 - 0xcd800000 ( 216 MB)
> modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> .init : 0xc0008000 - 0xc0022000 ( 104 kB)
> .text : 0xc0022000 - 0xc02e3000 (2820 kB)
> .data : 0xc02f8000 - 0xc0317860 ( 127 kB)
> Hierarchical RCU implementation.
> NR_IRQS:120
> VIC @fefb0000: id 0x00041190, vendor 0x41
> VIC @fefc0000: id 0x00041190, vendor 0x41
> Console: colour dummy device 80x30
> Calibrating delay loop... 99.73 BogoMIPS (lpj=498688)
> Security Framework initialized
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> ep93xx clock: PLL1 running at 400 MHz, PLL2 at 192 MHz
> ep93xx clock: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
> ep93xx dma_m2p: M2P DMA subsystem initialized
> ep93xx dma_m2m: M2M DMA subsystem initialized
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
> TCP: Hash tables configured (established 2048 bind 2048)
> TCP reno registered
> UDP hash table entries: 256 (order: 0, 4096 bytes)
> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> NET: Registered protocol family 1
> Trying to unpack rootfs image as initramfs...
> rootfs image is not initramfs (junk in compressed archive); looks like
> an initrd
> Freeing initrd memory: 4096K
> NetWinder Floating Point Emulator V0.97 (double precision)
> JFS: nTxBlock = 481, nTxLock = 3849
> msgmni has been set to 120
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Serial: AMBA driver
> apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
> console [ttyAM0] enabled
> apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
> apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
> brd: module loaded
> No NAND device found.
> ep93xx_mii_bus: probed
> ep93xx_eth:ep93xx_mii_probe: PHY supports MII frame preamble suppression
> ep93xx_eth:ep93xx_mii_probe: attached PHY driver [Generic PHY]
> (mii_bus:phy_addr =0:01, irq=-1)
> net eth0: ep93xx on-chip ethernet, IRQ 39, 00:d0:69:41:51:cb
> ep93xx-rtc ep93xx-rtc: rtc core: registered ep93xx-rtc as rtc0
> rtc-m48t86 rtc-m48t86: rtc core: registered m48t86 as rtc1
> rtc-m48t86 rtc-m48t86: battery ok
> ts72xx-wdt ts72xx-wdt: TS-72xx Watchdog driver
> TCP cubic registered
> NET: Registered protocol family 17
> rtc-m48t86 rtc-m48t86: setting system clock to 2010-10-12 15:47:26 UTC
> (12868984 46)
> RAMDISK: ext2 filesystem found at block 0
> RAMDISK: Loading 1536KiB [1 disk] into ram disk... done.
> EXT2-fs (ram0): warning: mounting unchecked fs, running e2fsck is
> recommended
> VFS: Mounted root (ext2 filesystem) on device 1:0.
> Freeing init memory: 104K
> >> Booting to SD Card...
> ts72xx-sdcard ts72xx-sdcard.0: SD card hardware revision: 00000000
> ts72xx-sdcard ts72xx-sdcard.0: block device major number = 254
> ts72xx-sdcard ts72xx-sdcard.0: New SD card detected, name=tssdcarda
> size=990976 (sectors)
> tssdcarda: tssdcarda1 tssdcarda2 tssdcarda3 tssdcarda4
> jfs: Unrecognized mount option "relatime" or missing value
> Mount failed for selinuxfs on /selinux: No such file or directory
> INIT: version 2.86 booting
>
>
> This e-mail, including any attachments and response string, may contain proprietary information which is confidential and may be legally privileged. It is for the intended recipient only. If you are not the intended recipient or transmission error has misdirected this e-mail, please notify the author by return e-mail and delete this message and any attachment immediately. If you are not the intended recipient you must not use, disclose, distribute, forward, copy, print or rely on this e-mail in any way except as permitted by the author.
>
__._,_.___
![]()
__,_._,___
|