Re: [ts-7000] How to setup FTP on TS-7250 SBC?

["Eric Robishaw" <>]

you need a small hub.
Also, if you're directly linking the SBC to the PC, you have to use a network cross-wire cable.

On Sun, Sep 7, 2008 at 8:37 PM, Yuping Dong <> wrote:

Thank you all for your help!
I have a simple question. My Linux system on my PC was installed through the university's network. So I can not use it offline.
When the SBC occupies the PC's eth port, PC cannot work properly, because my PC doesn't have a wireless connection.
How would you guys do at this circumstance?

Thanks,
Yuping

On Sun, Sep 7, 2008 at 6:11 PM, Eric Robishaw <> wrote:

It's likely a networking issue.  Unless your router is setup to 192.168.0.xx your device is not actually going to show up on the network or be reachable.

You'll likely have to change the ip address of the device to match your network.

So, if your router is on 192.168.3.1, for example, or 192.168.1.1 (typical defaults), then you'll need to change the device's ip address to 192.168.3.xx, or 192.168.1.xx.

You change the ip address in: /etc/network/interfaces
You may also need to setup your dns for the device (though not needed for what you're doing) (/etc/resolv.conf)
after making the changes:

ifdown eth0
ifup eth0

Eric

On Sun, Sep 7, 2008 at 11:50 AM, Yuping Dong <> wrote:

Hi Everyone,

I used the crosstool to compile my C code into arm binary file.
Now I want to upload this file to the TS-7250 SBC through FTP as said in the "Linux for ARM on TS-72XX" manual.
But when I typed "ftp 192.168.0.50", I got "-sh: ftp: not found ". I "/sbin/ifconfig", and the result is like this:
eth0      Link encap:Ethernet  HWaddr 00:D0:69:41:22:E2                        
          inet addr:192.168.0.50  Bcast:192.168.0.255  Mask:255.255.255.0      
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1                   
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0                   
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0                 
          collisions:0 txqueuelen:1000                                         
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)                               
          Interrupt:39                                                         
                                                 ;                               
lo        Link encap:Local Loopback                                            
          inet addr:127.0.0.1  Mask:255.0.0.0                                  
          UP LOOPBACK RUNNING  MTU:16436  Metric:1                             
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0                   
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0                 
          collisions:0 txqueuelen:0                                            
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)        

I don't know what is the problem? Do I have to setup an FTP separately before "ftp 192.168.0.50"? How to?

Thanks!

Yuping

__._,_.___

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe

__,_._,___