ts-7000
[Top] [All Lists]

[ts-7000] TS 7400 Seg Fault with zd_b driver

To:
Subject: [ts-7000] TS 7400 Seg Fault with zd_b driver
From: "mattfishburn" <>
Date: Fri, 08 Feb 2008 02:54:45 -0000
I have a TS-7400 that is straight out of the box.  I've tried to use
the IOGear GWU253 USB Wifi device but I get a Seg Fault.  Has anyone
had this issue before?  Is there a simple way to solve this?

Exact set of steps:

0) Kernel on my SD card inserts a bunch of modules on boot: usbcore zd
pcipool usb-ohci usb-ohci-ep93xx af_packet
1) I then run, as root,

# insmod /lib/modules/2.4.26-ts11/kernel/net/zd_b.o

2) output of dmesg:

...
Mounted devfs on /dev
Freeing init memory: 72K
sdcard0: Technologic Systems SD card controller, address 0x13000000
sdcard0: card size 990976 sectors
Partition check:
 sdcard0a: p1 p2 p3
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
zd1211 - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb.c: registered new driver zd1211
usb-ohci.c: USB OHCI at membase 0xe0020000, IRQ 56
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
ZD1211B - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb.c: registered new driver zd1211b

2) I insert the IOGear module into the usb port.  New output of dmesg:

...
ZD1211B - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb.c: registered new driver zd1211b
hub.c: new USB device not_pci-3, assigned address 2
Release Ver = 4810
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4810
zd1211:USB Download Boot code success
zd1211:MAC address = 00:02:72:6a:e0:c8
zd1211:AddrEntryTable = f7c6
zd1211:RF_Mode = 80000584
PA type: 0
Airoha AL2230S_RF
zd1211:Pure B-Mode
zd1211:AllowedChannel = 000007ff
zd1211:LinkLEDn = 200
AllowedChannel = 000107ff
Region:16
zd1205: (exit) zd1205_config, src/zd1205.c line 2601
zd1205: (exit) zd1205_init, src/zd1205.c line 8570

3) I attempt to up the interface and get a seg fault:

:root# ifconfig wlan0 up
Segmentation fault

New output of dmesg:

Region:16
zd1205: (exit) zd1205_config, src/zd1205.c line 2601
zd1205: (exit) zd1205_init, src/zd1205.c line 8570
zd1205: (enter) zd1205_close, src/zd1205.c line 4896
Unable to handle kernel NULL pointer dereference at virtual address
00000004
pgd = d17cc000
[00000004] *pgd=040b8801, *pmd = 040b8801, *pte = 00000000, *ppte =
00000000
Internal error: Oops: 7
CPU: 0
pc : [<d408ea7c>]    lr : [<d408ec04>]    Not tainted
sp : d17c1ec8  ip : 60000013  fp : 00000000
r10: 00000000  r9 : 00000000  r8 : d17c1f48
r7 : 00000000  r6 : 00000e94  r5 : d37b0000  r4 : 00000000
r3 : 00000000  r2 : d37b0e94  r1 : d37b0ab8  r0 : d37b0000
Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  Segment user
Control: C000317F  Table: E17CC000  DAC: 00000015
Process ifconfig (pid: 413, stack limit = 0xd17c0368)
Stack: (0xd17c1ec8 to 0xd17c2000)
1ec0:                   d37b0000 d37b0000 00000000 00000000 d17c1f48
d408ec04 
1ee0: 00000000 d409099c 00001320 d1074200 d107422c c02ebb84 d1074200
00001043 
1f00: 00001002 c02ed19c 00000000 00000000 d1074200 7ffffc7c c0321740
00000014 
1f20: 00000000 00008914 00001043 0001d44c 7fffff01 00000003 6e616c77
00000030 
1f40: 00000000 00000000 00001043 0001d44c 7fffff01 00000003 00008914
7ffffc7c 
1f60: d11b4320 00000004 ffffffe7 d17c0000 2abe9884 00000000 c02e4bf8
c026b7e0 
1f80: 00000000 d107b6bc 7ffffc7c 7ffffd04 00000041 00000036 c022c704
2abe9884 
1fa0: 00000000 c022c560 7ffffc7c c022c4fc 00000004 00008914 7ffffc7c
00001043 
1fc0: 7ffffc7c 7ffffd04 00000041 0001d8f4 2abead28 7ffffe1c 2abe9884
00000000 
1fe0: 0001dd4c 7ffffc7c 00009414 2ab8f934 60000010 00000004 00000000
00001510 
Backtrace: no frame pointer
Code: e3a07000 e3a06ee9 e2866004 e5954e94 (e5942004) 



 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU