Hi,
I am trying to use the usblib for the TS7400. I followed this
instructions but I could not make this example work .
I had no problem until step 7), so I think the problem is in step 8)
or 9).
Could somebody tell me how do I have to cross compile the sample program?
Thanks in advance,
Pablo
--- In Dino Sbrocca <> wrote:
>
> Anand,
>
> I have achieved some level of success.
>
> 1. I re-installed my cross toolchain from the TS web site
(ftp://ftp.embeddedarm.com/ts-arm-linux-cd/cross-toolchains/crosstool-linux-gcc-3.3.4-glibc-2.3.2-0.28rc39.tar.bz2)
> 2. I downloaded and unpacked the latest source for libusb
(http://prdownloads.sourceforge.net/libusb/libusb-0.1.12.tar.gz)
> 3. I ran the following configure command. The problem with the
command that I sent to you previously was that it wasn't overriding
the c++ compiler which is now required by version 0.1.12. The old
command caused the make utility to use the native c++ compiler. (
CC=arm-linux-gcc CXX=arm-linux-gcc ./configure
--prefix=/usr/local/opt/crosstool/arm-linux/gcc-3.3.4-glibc-2.3.2/arm-linux
--program-prefix=arm-linux- --host=arm-pc-linux-gnu)
> 4. I ran the make command (make). This command will successfully
compile all of the libusb core code and fail when it tries to compile
the libusb test programs. I ignored the test programs.
> 5. I adopted root authority (su)
> 6. I added the cross compiler to my path. The new install process
performs a compile.
(PATH=$PATH:/usr/local/opt/crosstool/arm-linux/gcc-3.3.4-glibc-2.3.2/bin)
> 7. I ran the install (make install). This command will
successfully install all core libusb objects and fail when it tries to
install the libusb test programs. I ignored the test programs.
> 8. I ftp'ed the libusb-0.1.so.4 file over to the /lib directory on
the TS7260.
> 9. I cross compiled my test program and tested it on the TS7260.
It worked.
>
> I will continue to investigate the failure of the libusb test programs.
>
> Dino Sbrocca <> wrote:
Anand,
>
> I downloaded the libusb source and tried to cross compile it from
scratch on my SUSE linux host. It failed.
>
> The .so binary that I have installed in my cross compile
environment and on my TS7260 is libusb-0.1.4.4.0. This is an older
version of libusb than the one I downloaded. I do not have the
original source that I used. I will never make that mistake again.
>
> I'll start over from scratch now and contact the libusb mailing
list for help. I'll keep detailed notes and send them to you when it
works.
>
> Dino
>
> Anand S Madhusoodanan <> wrote:
> Hi Dino,
>
> I tried out the things you had mentioned in your previoue email.
They worked until I typed in the make command.
>
> At the make command it gave me an error saying it could not read the
> .so file.
>
> "libusb.so: could not read symbols: File in wrong format"
>
> The exact mesage is pasted above.
>
> Is there is a problem with the version of software that I am using?
I had downloaded the Linux Crosstool gcc-3.3.4-glibc-2.3.2 -- 0.28rc39
(11-3-2004) from the website.
>
> I look forward to your comments.
>
> Regards
> Anand S Madhusoodanan
>
>
>
>
>
> Dino Sbrocca <> wrote:
> I use libusb to communicate with a USB interface chip to a
1-Wire network. I'm certainly not a linux expert but, the following
may help.
>
> To install libusb on the TS7260 I downloaded the source to libusb
to a host linux machine and cross compiled it using the following
commands:
>
> CC=arm-linux-gcc ./configure
--prefix=/usr/local/opt/crosstool/arm-linux/gcc-3.3.4-glibc-2.3.2/arm-linux
--program-prefix=arm-linux- --host=arm-pc-linux-gnu
> make
> make install
>
> I then ftp'ed the .so file to the TS7260 and set the proper
authorities.
>
> To run a test program, I first load the USB modules on the TS7260
with TS's /usr/bin/loadUSBModules.sh script and then mount the USB
file system with the following command:
>
> mount -t usbdevfs none /proc/bus/usb
>
> The test program was cross compiled on the host and then ftp'ed to
the TS7260. The test program just reads through the buses and devices
recognized by the kernal and dumps them to the console. It's a
reasonably good test that you've loaded all the software properly.
Send me an e-mail if you want the source.
>
> Dino
>
>
>
>
>
>
>
> Anand S Madhusoodanan <> wrote:
Hi,
>
> Has anyone used libusb on the TS7260? Any comments on how to go
about using that package on the board would be greatly appreciated.
>
> Regards
> Anand S Madhusoodanan
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam? Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
>
>
>
>
>
> ---------------------------------
> Yahoo! Music Unlimited - Access over 1 million songs. Try it free.
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|