On Tue, 17 Oct 2006, domniveust wrote:
> I have a TS-7250 and a PRISMIQ USB wireless adapted. I've set the
> adapter up using the instructions found here. My problem is that I
> cannot connect using the wireless, though it seems to be setup when I
> run iwconfig. It even shows the MAC address of my access point.
What do you mean you cannot connect?
from the data below it looks like you have both your ethernet interface
and wireless interface on the same network 192.168.1.0/24. It is usual to
have interfaces on seperate networks, or to have procedures for shutting
down the eth0 interface when testing.
What is your routing table like?
from another host can you ping the IP address of wlan0?
>
> ifconfig gives me the following:
>
> eth0 Link encap:Ethernet HWaddr 00:D0:69:40:50:93
> inet addr:192.168.1.216 Bcast:192.168.1.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:1198 errors:0 dropped:0 overruns:0 frame:0
> TX packets:664 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
> Interrupt:39
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>
> wlan0 Link encap:Ethernet HWaddr 00:12:0E:10:15:77
> inet addr:192.168.1.219 Bcast:192.168.1.255
> Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:271 errors:3 dropped:0 overruns:0 frame:3
> TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:82049 (80.1 KiB) TX bytes:36 (36.0 B)
>
> ------------------------------------------------------------------------\
> ---------------------
>
> iwconfig gives me the following:
>
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> Warning : Device wlan0 has been compiled with a different version
> of Wireless Extension than ours (we are using version 10).
> Some things may be broken...
>
> wlan0 802.11b/g NIC ESSID:"AP_main"
> Mode:Managed Frequency:2.462GHz Access Point:
> 00:14:6C:33:CE:68
> Bit Rate:1Mb/s
> RTS thr=2432 B Fragment thr:off
> Encryption key:off
> Power Management:off
> Link Quality:92/116 Signal level:69/95 Noise level:7/114
> Rx invalid nwid:0 invalid crypt:0 invalid misc:0
>
> I'm assuming my problem is with the different version of wireless
> extension. How do I fix that?
>
> Thanks for any help.
>
> Ben Maderazo
>
>
>
>
>
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|