WOW you made fast progress.
A couple quick notes:
.org 2048 @ ensures the file is 2k in
size. (no more, no less)
.end
The .org command is there to cause an error if you go over the 2048 byte limit
of the eeprom. The EP9302 will only load 2048 bytes from the eeprom so
anything over will not be loaded at boot time.
I've started working on a new version of the SerialBlaster that can boot from
an 8KB eeprom. I soldered off the 2KB eeprom and replaced it with a 8KB
eeprom (was easy to do). The new SerialBlaster boots in two stages. It first
boots the initial 2KB which then loads the additional 6KBs boot loader.
You can get a version of the default TS eeprom and redboot images and burn
them using my serialblaster.
-Curtis.
On September 2, 2006 01:20 pm, Tom Hansen wrote:
> I was able to get the board booting into Redboot from flash again by
> doing the following:
>
> ("Host" refers to the PC being used to rescue the board, "Board"
> refers to the board)
>
> 1. Host: Downloaded SerialBlaster from the Files section of this
> Yahoo group.
> 2. Host: Built it according to the included directions.
> 3. Board: Installed a jumper on JP1.
> 4. Host/Board: Booted the board using the newly-build SerialBlaster.
> 5. Host: Went into boot.S and changed it to boot in FLASH mode.
> and got rid of .org 4096 thing (yes it works anyway)
> 6. Host: make clean; make in serialblaster directory.
> 7. Host/Board: booted with SerialBlaster.
> 8. Above boot only loads boot.bin, then proceeds directly to the
> redboot loaded at the previous boot, since it is now in FLASH mode.
> 9. Board: Used the following commands on board:
>
> load -v -r -b 0x00200000 -m xmodem
>
> 10. Host: transmitted boot.bin to board with xmodem.
> 11. Board: burned boot to EEPROM with the following command:
>
> eeprom_write -b 0x00200000 -o 0 -l 2048
>
> 12. Board: Now system boots completely from flash.
>
>
> Some particular notes:
>
> a) Regarding step 5, I tried to retain the boot.bin as originally
> compiled, but it would never proceed to Redboot by itself, apparently
> staying in serial mode and trying to load Redboot from serial rather
> than from flash, thus requiring a rebuild after changing the
> definitions in boot.S to indicate FLASH mode. However it then
> complained about going backwards (or some such) with the .org 4096
> thing. I did see a post by Curtis in which he said the org 4096 thing
> was required. I tried very hard to retain it, but in the end I left
> it off and it just worked.
>
> b) All attempts to reflash original TS components (EEPROM and Redboot)
> have failed. This is a slight problem because the SerialBlaster
> version of Redboot doesn't appear to initialize USB correctly, and
> that's where my root NetBSD filesystem is. The failure to reflash the
> original components probably has to do with differences between the
> 7250 for which SerialBlaster was written, and the 7260 which I have.
>
> c) Apparently the SerialBlaster versions of EEPROM/Redboot do not make
> such extensive use of the "(reserved)" area of flash, because I was
> able to write (but not successfully boot from) a NetBSD kernel into
> the reserved space without crashing the board. The board still booted
> into RedBoot after I did that.
>
>
> I'll post further developments as they occur.
>
>
> --- In Curtis Monroe <> wrote:
> >
> > You might try my SerialBlaster utility (search old posts).
> >
> > I built it for a TS-7250 but it might still work for the TS-7260.
> >
> > Or you can send it back to TS for a reflash.
> >
> > -Curtis.
> >
>
>
>
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|