Thanks Don for answering! I may be having the same issue you had. Now my question is, which Debian image did you finally use?
I´d like to use a Sarge distribution so I looked at the site ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7260-linux/distributions/ but I am not sure if it should be ""debian-sarge-256MB-05-01-2006.tar.bz2" or "debian-sarge-usb_default.tar.gz"
sorry, I am kind of newbie so I would really appreciate any help
Luis
2011/2/7 Don Tucker <>
The USB Debian image that I received with the TS7260 development kit was
broken. I contacted tech support, and they confirmed that there was a
problem with the USB sticks that they were using, and they pointed me
toward another USB image (on their ftp site) that I dd'd onto a new USB
flash drive and it was able to boot fine.
Don
On 2/3/2011 9:34 PM, deboxur wrote:
>
> Hi, I am trying to boot Debian which is hosted in my USB flash drive.
> I am using TS-7260. I followed all the steps as in the manual but
> getting the same error as below:
>
> EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
> chroot: cannot execute /etc/init.d/rcS.USB: No such file or directory
> umount: /mnt/cf/proc/bus: No such file or directory
> umount: /mnt/cf/dev/pts: Invalid argument
> umount: /mnt/cf/proc: Invalid argument
>
> I found this post on the group so I was wondering if I could get some
> help, I would really appreciate it
>
> PD: I placed the USB flash drive in the BOTTOM and TOP USB port, but
> still getting same error, so it is not the issue
>
> --- In <mailto:ts-7000%2540yahoogroups.com>, Don
> Tucker <> wrote:
> >
> > I get those messages if the USB flash is not plugged into the USB port.
> > Do you have your USB flash drive plugged into the BOTTOM USB port on
> the
> > board?
> >
> > Don
> > On 11/12/2010 9:09 AM, spencerottarson wrote:
> > >
> > > I have followed the instructions exactly, including the fsck. When I
> > > run loadUSB.sh, it gives me these messages:
> > >
> > > chroot: cannot execute /etc/init.d/rcS.USB: No such file or directory
> > > umount: /mnt/cf/proc/bus: No such file or directory
> > > umount: /mnt/cf/dev/pts: Invalid argument
> > > umount: /mnt/cf/proc: Invalid argument
> > >
> > > I used the Debian sarge image for the 2.4 kernel directly from the
> > > embeddedarm website.
> > >
> > > --- In <mailto:ts-7000%2540yahoogroups.com>
> <mailto:ts-7000%2540yahoogroups.com>, Don
> > > Tucker <dtucker@> wrote:
> > > >
> > > > Checkout section 5.2, Updating the EXT2 Image, from the
> > > > linuxforarm-manual.pdf for instructions on how to set up the USB
> drive
> > > > for boot. The instructions say to use tar -xfvj, but the j is
> for bzip.
> > > > Use the appropriate tar argument for a gzipped file.
> > > >
> > > > Don
> > > >
> > > > On 11/11/2010 5:23 PM, spencerottarson wrote:
> > > > >
> > > > > I am using the 2.4 kernel. I am new to this kind of stuff, and
> i do
> > > > > not know how to compile a kernel myself, or edit the initrd.
> > > > > Another question about how to put the debian image on the usb
> flash
> > > > > drive. I have downloaded the .tar.gz file from the embedded arm
> > > > > website, but what am I supposed to do with it? Do i just put it
> > > > > directly on the flash drive, or extract it first, or something
> else?
> > > > >
> > > > >
> > > >
> > >
> > >
> >
>
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
__._,_.___
![]()
__,_._,___
|