ts-7000
[Top] [All Lists]

[ts-7000] Re: Modprobe, ttyS, boot (solved)

To:
Subject: [ts-7000] Re: Modprobe, ttyS, boot (solved)
From: "kf8ki" <>
Date: Wed, 31 Mar 2010 21:40:46 -0000
Found it.  Not sure why but setserial and etc-setserial were running at startup 
on the problem system.

update-rc.d -f setserial remove
update-rc.d -f etc-setserial remove

If these are necessary apps, comments to that effect are welcome.  They aren't 
running on the other system though and it's been in service for 6 months or 
more, so I'm inclined to doubt it.

Hope this helps someone.

Steve


--- In  Steve Weigold <> wrote:
>
> 
> Friends,
> 
> I need a push in the right direction.  I'm getting the modprobe messages 
> during boot about the ttyS module as seen in the clip below.  For the 
> life of me, I can't get rid of them.  I've compared the setup on this 
> system to another working system to the extent I know how, and I don't 
> see what's getting loaded here that would need the ttyS module that 
> isn't getting loaded on the other system.
> 
> System is a TS-7200 booting to CF running Debian Sarge.
> 
> If someone could suggest places to look, I'd appreciate it.  I see no 
> errors in syslog or dmesg.
> 
> Steve
> 
> <---------------- boot messages ------------------------------>
> pcipool usb-ohci usb-ohci-ep93xx usb-ohci.c: USB OHCI at membase 
> 0xe0020000, IRQ 56
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 3 ports detected
> af_packet
> Checking all file systems...
> fsck 1.37 (21-Mar-2005)
> modprobe: Can't locate module ttyS?? which is needed for /dev/ttyS??
> modprobe: Can't locate module ttyS?? which is needed for /dev/ttyS??
> ... done.
> Setting up networking...done.
> Starting hotplug subsystem: usb isapnp ide scsi.
> Setting up IP spoofing protection: rp_filter.
> Enabling packet forwarding...done.
> Configuring network interfaces...done.
> modprobe: Can't locate module ttyS?? which is needed for /dev/ttyS??
> modprobe: Can't locate module ttyS?? which is needed for /dev/ttyS??
> Loading the saved-state of the serial devices...
> Recovering nvi editor sessions... done.
> INIT: Entering runlevel: 2
> 
> <---------------- boot messages ------------------------------>
>




------------------------------------

Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU