ts-7000
[Top] [All Lists]

Re: [ts-7000] Corrupted flas recovery

To:
Subject: Re: [ts-7000] Corrupted flas recovery
From: Daniel Smolik <>
Date: Sun, 25 Oct 2009 18:16:21 +0100
Petr Štetiar napsal(a):
> 
>
> Daniel Smolik < <marvin%40mydatex.cz>>
> [2009-10-25 17:39:11]:
>
>  > Hi all, I have problem with recovering completely erased flash on
> TS-7200.
>  > I by mistake erased whole flash on TS-7200 with flash_eraseall. I
> have boot
>  > to TS-9420 and see /dev/mtd1 - /dev/mtd6. I flashcp /dev/mtd3
> tsbootrom.bin.
>  > After this board start booting on serial console is displayed information
>  > about TS-BOOTROM but after this "Could not find CRUS signature" is
>  > displayed. It's much better than on start. After this I try flash redboot
>  > with flashcp. But I get "no such device". In /proc/mtd I see
> /dev/mtd4 and
>  > mtd5 but I can't use it. Have anybody experience with TS-9420 ?
>
> My notes for ts-7250, hope it helps:
>
> Restore redboot
> ---------------
>
> 1) load redboot to RAM
> JP1 on
> JP2 off
> JP3 on
> #./serial_blaster
>
> serialblaster will finish with this error:
>
> waiting for ']'
> found ']'
> ReadByte ERROR, no input after 60 seconds
>
> don't reset board!, continue with 2)
>
> 2) enable serial console
> JP1 on
> JP2 on <- enables serial console
> JP3 on
> run minicom or whatever
> there should be a 'RedBoot>' prompt
>
> 3) load RedBoot to RAM
> RedBoot> fis list
> Name FLASH addr Mem addr Length Entry point
> (reserved) 0x60000000 0x60000000 0x01D04000 0x00000000
> RedBoot 0x61D04000 0x61D04000 0x00040000 0x00000000
> FIS directory 0x61FFC000 0x61FFC000 0x00003000 0x00000000
> RedBoot config 0x61FFF000 0x61FFF000 0x00001000 0x00000000
>
> RedBoot> load -v -r -b 0x00218000 -m http -h 192.168.2.227
> /~ynezz/redboot-7250-32mb-10-26-2005.bin
> Raw file loaded 0x00218000-0x00513fff, assumed entry at 0x00218000
>
> count size:
> :~/public_html$ python -c "print(hex(0x002180000-0x00513fff))"
> 0x1c6c001
>
> RedBoot> fis write -f 0x61D04000 -b 0x00218000 -l 0x1c6c001
>

Thanks for reply,
I tested serial-blaster with another corrupted 7200 but doesn't have success.
But I restored previous board  with TS-9420. I try what you recommend me.
Thanks

                Dan














------------------------------------

Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
    
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU