ts-7000
[Top] [All Lists]

[ts-7000] TS-7250 doesn't resolve host name

To:
Subject: [ts-7000] TS-7250 doesn't resolve host name
From: "xie_jian_hua" <>
Date: Mon, 23 Apr 2007 15:40:23 -0000
I ran the ping command on my TS-7250 board and got the message:

$ping www.bankofamerica.com
ping: www.bankofamerica.com: Unknown host

If I ping an IP address instead of host name, it will work. My TS-7250
board is configured to use dhcp and should work fine since the output
from ifconfig command is:
$ ifconfig                                                           
      
eth0      Link encap:Ethernet  HWaddr 00:D0:69:40:3D:D7              
          
          inet addr:10.10.1.113  Bcast:10.255.255.255 
Mask:255.255.255.0       
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1         
          
          RX packets:1761 errors:0 dropped:0 overruns:0 frame:0      
          
          TX packets:2 errors:0 dropped:0 overruns:0 carrier:0       
          
          collisions:0 txqueuelen:1000                               
          
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)                     
          
          Interrupt:39                                               
          
                                                                     
          
I did search the previous messages. One said a similar problem was
caused by wrong static IP address used by the SBC. But I don't think
it applies to my situation because I have a Linux desktop on the same
subnet. It runs dhcp and resolves all host names. Running ifconfig
command on the desktop PC gives me the output:

eth1      Link encap:Ethernet  HWaddr 00:14:6C:C3:73:DE  
          inet addr:10.10.1.115  Bcast:10.10.1.255  Mask:255.255.255.0
          inet6 addr: fe80::214:6cff:fec3:73de/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3666226 errors:0 dropped:0 overruns:0 frame:0
          TX packets:903355 errors:360 dropped:0 overruns:4 carrier:720
          collisions:5470 txqueuelen:1000 
          RX bytes:1603262774 (1.4 GiB)  TX bytes:123856516 (118.1 MiB)
          Interrupt:16 Base address:0xef00 

If I put a host name and IP address pair in the /etc/hosts file, it
will work for that specific host name. My linux version is 2.4.26-ts9
Anybody can give me a pointer? Thank you.




 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/ts-7000/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/ts-7000/join
    (Yahoo! ID required)

<*> To change settings via email:
     
    

<*> To unsubscribe from this group, send an email to:
    

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 

<Prev in Thread] Current Thread [Next in Thread>
Admin

Disclaimer: Neither Andrew Taylor nor the University of NSW School of Computer and Engineering take any responsibility for the contents of this archive. It is purely a compilation of material sent by many people to the birding-aus mailing list. It has not been checked for accuracy nor its content verified in any way. If you wish to get material removed from the archive or have other queries about the archive e-mail Andrew Taylor at this address: andrewt@cse.unsw.EDU.AU