Thank you for your answer, but that's work now. It was about a
problem during the compact flash "mkfs".
Romain
--- In Christopher Friedt <>
wrote:
>
> You need to create the /dev/ttyAM0 node ... just look on a working
board
> for the major number with 'ls -l /dev/ttyAM0' - i don't have a
board
> handy, so i can't tell you the major number at the moment.
>
> The comand to create the node is:
>
> mknod /dev/ttyAM0 c <major> 0
>
> As for mount_devfs_fs failing - i can't suggest too much.
>
> Do you have a /dev directory? ... you could always look in the
kernel
> source for mount_devfs_fs() and determine which conditions generate
a -2.
>
> ~/Chris
>
>
> bowbaq74000 wrote:
> > Hi,
> >
> > I want to try to boot with Debian from my compact flash card.
> > I use 1 Go Flash card. I follow steb-by-step the Linux guide
(page 25) :
> > 1) execute the fdisk command (create a new partition, activate
the boot
> > sector)
> > 2) use the mkfs.ext2 command
> > 3) unpack the debian image tarball (debian-sarge 1.09)
> > 4) fsck command
> >
> > But, when I try to boot with my TS7200 I have this message :
> >
> > == Executing boot script in 0.100 seconds - enter ^C to abort
> > RedBoot> fis load vmlinux -b 0x00218000
> > RedBoot> exec -c "console=ttyAM0,115200 ip=dhcp root=/dev/hda1"
> > Using base address 0x00218000 and length 0x000c0000
> > Linux version 2.4.26-ts11 (gcc version
3.3.4)
> > #215 Thu J6
> > CPU: Arm920Tid(wb) revision
> > Machine: ep9301
> >
> > [...]
> >
> >
> > Technologic Systems TS-7XXX IDE initialization - driver version
1.3,
> > 6/21/04.
> > hda: SanDisk SDCFH-2048, CFA DISK drive
> > ide0 at 0x8d000000-0x8d000007,0x88400006 on irq 32
> > hda: attached ide-disk driver.
> > hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete
Error }
> > hda: task_no_data_intr: error=0x04 { DriveStatusError }
> > hda: 4001760 sectors (2049 MB) w/1KiB Cache, CHS=3970/16/63
> > Partition check:
> > /dev/ide/host0/bus0/target0/lun0: [PTBL] [249/255/63] p1
> > TS-7200 flash: Found 1 x16 devices at 0x0 in 16-bit bank
> > Intel/Sharp Extended Query Table at 0x0031
> > Using buffer write method
> > cfi_cmdset_0001: Erase suspend on write enabled
> > Creating 3 MTD partitions on "TS-7200 flash":
> > 0x00000000-0x00020000 : "TS-BOOTROM"
> > 0x00020000-0x00620000 : "Linux"
> > 0x00620000-0x00800000 : "RedBoot"
> > NET4: Linux TCP/IP 1.0 for NET4.0
> > IP Protocols: ICMP, UDP, TCP, IGMP
> > IP: routing cache hash table of 512 buckets, 4Kbytes
> > TCP: Hash tables configured (established 2048 bind 4096)
> > Sending DHCP requests .., OK
> > IP-Config: Got DHCP answer from 0.0.0.0, my address is
192.168.100.212
> > IP-Config: Complete:
> > device=eth0, addr=192.168.100.212, mask=255.255.255.0,
> > gw=192.168.100.202,
> > host=192.168.100.212, domain=anator, nis-domain=(none),
> > bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
> > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> > NetWinder Floating Point Emulator V0.97 (double precision)
> > /dev/ide/host0/bus0/target0/lun0: p1
> > /dev/ide/host0/bus0/target0/lun0: p1
> > VFS: Mounted root (ext2 filesystem).
> > mount_devfs_fs(): unable to mount devfs, err: -2
> > Freeing init memory: 72K
> > Warning: unable to open an initial console.
> > Kernel panic: No init found. Try passing init= option to kernel.
> >
> >
> > What is my mistake ???
> >
> > thanks
> > regards,
> >
> >
> >
> >
>
------------------------ Yahoo! Groups Sponsor --------------------~-->
Yahoo! Groups gets a make over. See the new email design.
http://us.click.yahoo.com/hOt0.A/lOaOAA/yQLSAA/CFFolB/TM
--------------------------------------------------------------------~->
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|