[ts-7000] [TS - 7200] problem vith Debian boot

["bowbaq74000" <>]

Hi,

I want to try to boot with Debian from my compact flash card.
I use 1 Go Flash card. I follow steb-by-step the Linux guide (page 25) : 
1) execute the fdisk command (create a new partition, activate the boot sector)
2) use the mkfs.ext2 command 
3) unpack the debian image tarball (debian-sarge 1.09)
4) fsck command

But, when I try to boot with my TS7200 I have this message :

== Executing boot script in 0.100 seconds - enter ^C to abort 
                  RedBoot> fis load vmlinux -b 0x00218000 
                                        RedBoot> exec -c "console=ttyAM0,115200 ip=dhcp root=/dev/hda1" 
                Using base address 0x00218000 and length 0x000c0000 
                            Linux version 2.4.26-ts11  (gcc version 3.3.4) #215 Thu J6
CPU: Arm920Tid(wb) revision 
                                                      Machine: ep9301 
     
[...]

                 !
                                            
    Technologic Systems TS-7XXX IDE initialization - driver version 1.3, 6/21/04. 
  hda: SanDisk SDCFH-2048, CFA DISK drive 
                                        ide0 at 0x8d000000-0x8d000007,0x88400006 on irq 32 
                             hda: attached ide-disk driver. 
                                                 hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error } 
          hda: task_no_data_intr: error=0x04 { DriveStatusError } 
                        hda: 4001760 sectors (2049 MB) w/1KiB Cache, CHS=3970/16/63 
                    Partition check: 
                                                                /dev/ide/host0/bus0/target0/lun0: [PTBL] [249/255/63] p1 
                      TS-7200 flash: Found 1 x16 devices at 0x0 in 16-bit bank 
                        Intel/Sharp Extended Query Table at 0x0031 
                                    Using buffer !
 write method 
                                             !
         
 cfi_cmdset_0001: Erase suspend on write enabled 
                                Creating 3 MTD partitions on "TS-7200 flash": 
                                  0x00000000-0x00020000 : "TS-BOOTROM" 
                                           0x00020000-0x00620000 : "Linux" 
                                                0x00620000-0x00800000 : "RedBoot" 
                                              NET4: Linux TCP/IP 1.0 for NET4.0 
                                              IP Protocols: ICMP, UDP, TCP, IGMP 
                                             IP: routing cache hash table of 512 buckets, 4Kbytes 
                           TCP: Hash tables configured (established 2048 bind 4096) 
                       Sending DHCP requests .., OK 
                                                   IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.100.212 
         IP-Config: Complete: 
                                       !
                           device=eth0, addr=192.168.100.212, mask=255.255.255.0, gw=192.168.100.202,
     host=192.168.100.212, domain=anator, nis-domain=(none), 
                        bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= 
                         NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. 
                            NetWinder Floating Point Emulator V0.97 (double precision) 
                      /dev/ide/host0/bus0/target0/lun0: p1 
                                           /dev/ide/host0/bus0/target0/lun0: p1 
                                          VFS: Mounted root (ext2 filesystem). 
                                           mount_devfs_fs(): unable to mount devfs, err: -2 
                               Freeing init memory: 72K 
                                                       Warning: unable to open an initial console.

Kernel panic: ! No init found. Try passing init= option to kernel.


What is my mistake ???

thanks
regards,


__._,_.___

SPONSORED LINKS

Single board computer	Hardware	Computer running slow
Linux os	Single board

Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe

__,_._,___