Jaan
If I use your .config in my build environment I get the following
...
Uncompressing Linux... done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x0000020e).
Available machine support:
ID (hex) NAME
00000674 Technologic Systems TS-78xx SBC
Please check your kernel config and/or bootloader.
If I correct for this in mach_types.h, I get ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.7 (gcc version 4.3.2
(Debian 4.3.2-1.1) ) #10 PREEMPT Fri Oct 22 13:12:57 MST 2010
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=b0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Technologic Systems TS-78xx SBC
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 32512
Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 rw
init=/linuxrc
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 121424k/121424k available, 9648k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0027000 ( 124 kB)
.text : 0xc0027000 - 0xc03da000 (3788 kB)
.data : 0xc0416000 - 0xc04386c0 ( 138 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
TS-78xx FPGA: magic=0x00b480, rev=0x05
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks
like an initrd
Freeing initrd memory: 4096K
NetWinder Floating Point Emulator V0.97 (double precision)
NTFS driver 2.1.29 [Flags: R/O].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 980, nTxLock = 7845
msgmni has been set to 245
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:69:42:14:c7
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus
number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
orion-ehci orion-ehci.1: Marvell Orion EHCI
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
rtc-m48t86 rtc-m48t86: rtc core: registered m48t86 as rtc0
rtc-m48t86 rtc-m48t86: battery ok
i2c /dev entries driver
MV-CESA:Fallback driver 'sha1' could not be loaded!
alg: hash: Failed to load transform for mv-sha1: -2
MV-CESA:Fallback driver 'hmac(sha1)' could not be loaded!
alg: hash: Failed to load transform for mv-hmac-sha1: -2
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
ata1: SATA link down (SStatus 0 SControl 300)
VFP support v0.3: not present
rtc-m48t86 rtc-m48t86: setting system clock to 2010-10-22 20:21:20
UTC (1287778880)
ata2: SATA link down (SStatus 0 SControl 300)
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1536KiB [1 disk] into ram disk... done.
EXT2-fs (ram0): warning: checktime reached, running e2fsck is
recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 124K
>> Booting to SD Card...
tssdcard: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
usbcore: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
ehci_hcd: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
>> SD Card failed. Booting to initrd...
Finished booting in 6.39 seconds
Type 'tshelp' for help
/ # ts7800: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
tsuart1: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
tsuart7800: version magic '2.6.21-ts preempt mod_unload ARMv5 '
should be '2.6.35.7 preempt mod_unload ARMv5 '
eth0: link up, 100 Mb/s, full duplex, flow control disabled
/ #
++++++++++++++++++++++++++
All I need to do now is build the tssdcard module and see if it
works.
Ian T.
This e-mail, including any attachments and response string, may contain proprietary information which is confidential and may be legally privileged. It is for the intended recipient only. If you are not the intended recipient or transmission error has misdirected this e-mail, please notify the author by return e-mail and delete this message and any attachment immediately. If you are not the intended recipient you must not use, disclose, distribute, forward, copy, print or rely on this e-mail in any way except as permitted by the author.
__._,_.___
![]()
__,_._,___
|
|