|
Thank you Jason and Jim for your responses. --- In Jim Jackson <> wrote: > > > > The router type is Linksys WRT160Nv2, f/w rev v2.0.03. DHCP is enabled > > with start address 192.168.0.100. > > How many IP addresses in the pool? > Only about four, all dynamically assigned. > > NAT is enabled, DMZ is disabled, > > essentially all the settings are default. > > > > There is a straight Ethernet cable tied between the router and the > > TS-7200. Below is the terminal output on boot up: > > > > > >>> TS-BOOTROM, Rev 1.08 - built 10:44:37, May 26 2006 > >>> Copyright (C) 2006, Technologic Systems > >>> TS-7200: Rev >E1 CPU, Rev C PLD, 32MB SDRAM, options ( RS485 ) > > > > +Ethernet eth0: MAC address 00:d0:69:40:66:ce > > IP: 192.168.0.110/255.255.255.0, Gateway: 192.168.0.1 > > Default server: 192.168.0.1 > > > > RedBoot(tm) bootstrap and debug environment [ROMRAM] > > Non-certified release, version current-TS_5 - built 11:24:54, Jun 7 2006 > > > > Platform: TS-7200 Board (ARM920T) Rev A > > Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. > > > > RAM: 0x00000000-0x02000000, [0x00044f88-0x01fdd000] available > > FLASH: 0x60000000 - 0x60800000, 64 blocks of 0x00020000 bytes each. > > == Executing boot script in 0.100 seconds - enter ^C to abort > > RedBoot> fis load vmlinux > > RedBoot> exec -c "console=ttyAM0,115200 ip=dhcp root=/dev/hda1" > > You don't need ip=dhcp above. Take it out and retry. The kernel only needs > ip details if it is going to use e.g. NFS root partition. > I had suspected that ip=dhcp in the boot script wasn't needed but I tried it without and it didn't seem to work either. This is what I'm seeing: ts7200:~# cat /etc/network/interfaces Is there some problem with the dhclient configuration? > It maybe that the kernel is doing a dhcp and then useland dhcp is doing it > again, and there might be some interaction. > > > Using base address 0x00218000 and length 0x000c0000 > > Linux version 2.4.26-ts11 (gcc version 3.3.4) #215 Thu Jun 8 14:30:17 MST 2006 > > CPU: Arm920Tid(wb) revision 0 > > Machine: ep9301 > > On node 0 totalpages: 2048 > > zone(0): 2048 pages. > > zone(1): 0 pages. > > zone(2): 0 pages. > > On node 1 totalpages: 2048 > > zone(0): 2048 pages. > > zone(1): 0 pages. > > zone(2): 0 pages. > > On node 4 totalpages: 2048 > > zone(0): 2048 pages. > > zone(1): 0 pages. > > zone(2): 0 pages. > > On node 5 totalpages: 2048 > > zone(0): 2048 pages. > > zone(1): 0 pages. > > zone(2): 0 pages. > > Kernel command line: console=ttyAM0,115200 ip=dhcp root=/dev/hda1 > > Console: colour dummy device 80x30 > > Calibrating delay loop... 99.94 BogoMIPS > > Memory: 8MB 8MB 8MB 8MB = 32MB total > > Memory: 28500KB available (1320K code, 350K data, 72K init) > > Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) > > Inode cache hash table entries: 2048 (order: 2, 16384 bytes) > > Mount cache hash table entries: 512 (order: 0, 4096 bytes) > > Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) > > Page-cache hash table entries: 8192 (order: 3, 32768 bytes) > > CPU: Testing write buffer: pass > > POSIX conformance testing by UNIFIX > > Linux NET4.0 for Linux 2.4 > > Based upon Swansea University Computer Society NET3.039 > > Initializing RT netlink socket > > Starting kswapd > > devfs: v1.12c (20020818) Richard Gooch > > devfs: boot_options: 0x1 > > JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc. > > ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA > > ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA > > ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA > > pty: 1024 Unix98 ptys configured > > Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ enabled > > rtc: no TS-5620 RTC detected. > > ep93xx_eth() version: ep93xx_eth.c: V1.0 09/04/2003 Cirrus Logic > > Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 > > ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx > > Technologic Systems TS-7XXX IDE initialization - driver version 1.3, 6/21/04. > > hda: SanDisk SDCFB-1024, CFA DISK drive > > ide0 at 0x8d000000-0x8d000007,0x88400006 on irq 32 > > hda: attached ide-disk driver. > > hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error } > > hda: task_no_data_intr: error=0x04 { DriveStatusError } > > hda: 2001888 sectors (1025 MB) w/1KiB Cache, CHS=1986/16/63 > > Partition check: > > /dev/ide/host0/bus0/target0/lun0: [PTBL] [993/32/63] p1 > > TS-7200 flash: Found 1 x16 devices at 0x0 in 16-bit bank > > Intel/Sharp Extended Query Table at 0x0031 > > Using buffer write method > > cfi_cmdset_0001: Erase suspend on write enabled > > Creating 3 MTD partitions on "TS-7200 flash": > > 0x00000000-0x00020000 : "TS-BOOTROM" > > 0x00020000-0x00620000 : "Linux" > > 0x00620000-0x00800000 : "RedBoot" > > NET4: Linux TCP/IP 1.0 for NET4.0 > > IP Protocols: ICMP, UDP, TCP, IGMP > > IP: routing cache hash table of 512 buckets, 4Kbytes > > TCP: Hash tables configured (established 2048 bind 4096) > > Sending DHCP requests ...... timed out! > > IP-Config: Reopening network devices... > > Sending DHCP requests .... > > > > > > (and it continues forever...) > > > > Since my last post I was able to get the TS-7200 to successfully get an > > address by reserving an IP address on the router for the MAC of the > > TS-7200. DHCP is still enabled on the router, but it immediately > > recognizes the MAC and assigns the reserved IP. Hopefully that will help > > figure out why 'standard' DHCP isn't working. > > 'standard' DHCP ? Where I last did network management (I'm retired) > 'standard' DHCP was a huge table of fixed IP allocations matched to MACs. > There was a "pool" of IP for unknown machines but they didn't get > a default router allocated, and the syslog watcher soon told us when > unknown machines appeared. > > Do you really need the ability to pick up some random IP address? > Or is just as a convenience when moving it from network to network? > I always prefer my devices to have a known IP address - at least on the > "home" network. > I would like if possible to move the device to different networks as needed and not have to adjust the routers from their default settings. > > I'm not sure if there is any other information I can provide to figure > > this out - if so, please let me know, and thanks for any help you can > > offer. > > > > Angelo > > > > > > > > > > > > > __._,_.___
Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required) Change settings via email: =Email Delivery: Digest | m("yahoogroups.com?subject","ts-7000-fullfeatured");=Change Delivery Format: Fully Featured">Switch to Fully Featured Visit Your Group | Yahoo! Groups Terms of Use | =Unsubscribe __,_._,___ |