Hi,
I'm running my TS-7400 with modifications to the hwclock scripts as described
in this thread:
http://tech.groups.yahoo.com/group/ts-7000/message/17097
I am attempting to use my IOGear GWU523 with the device, however the zd1201
driver doesn't seem to claim the device. I've checked that the driver is
listed in lsmod output, and the device clearly shows up in the dmesg output.
Am I missing a step to link the driver to claiming the USB device? Here is my
dmesg output (I plugged the USB WIFI adapter in after the board had booted).
ts7000:~# dmesg
Linux version 2.6.29-ts (gcc version 3.4.4
(release) (CodeSourcery ARM 2005q3-2)) #4 PREEMPT Sun May 17 15:02:44 MST 2009
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: Technologic Systems TS-72xx SBC
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
Normal zone: 7344 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 9040 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 9040
Kernel command line: root=/dev/ram0 rw init=/linuxrc lpj=498688 console=null
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 8MB 8MB 8MB 8MB 8MB 8MB 8MB 8MB = 64MB total
Memory: 57412KB available (2912K code, 210K data, 116K init)
Calibrating delay loop (skipped) preset value.. 99.73 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 760 bytes
NET: Registered protocol family 16
ep93xx: PLL1 running at 400 MHz, PLL2 at 192 MHz
ep93xx: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 4096K
NetWinder Floating Point Emulator V0.97 (extended precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
JFS: nTxBlock = 480, nTxLock = 3845
msgmni has been set to 120
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
brd: module loaded
ep93xx-eth version 0.11 loading
eth0 (): not using net_device_ops yet
ep93xx_mii_bus: probed
Generic PHY 0:01: PHY supports MII frame preamble suppression
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: ep93xx on-chip ethernet, IRQ 39, 00:d0:69:41:00:7d
rtc-m48t86 rtc-m48t86: rtc core: registered m48t86 as rtc0
rtc-m48t86 rtc-m48t86: battery ok
ep93xx_wdt: EP93XX watchdog, driver version 0.3
ts72xx_wdt: cannot register miscdev on minor=130 (err=-16)
ts72xx-wdt: probe of ts72xx-wdt failed with error -16
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m48t86 rtc-m48t86: hctosys: invalid date/time
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1536KiB [1 disk] into ram disk... done.
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 116K
Warning: unable to open an initial console.
Searching for NAND flash...
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V
8-bit)
Bad block table found at page 65504, version 0x01
Bad block table found at page 65472, version 0x01
Hardware ECC NOT detected!
Using MBR partition definition
Creating 4 MTD partitions on "NAND 32MiB 3,3V 8-bit":
0x000000000000-0x000002000000 : "whole chip"
0x000000004000-0x000000204000 : "kernel"
0x000000204000-0x000000404000 : "initrd"
0x000000404000-0x000002000000 : "rootfs"
tssdcard: Technologic Systems SD card controller, address 0xe8000100
size=0xf1f00
size=0xf1f00
tssdcard: card /dev/tssdcarda has 990976 sectors (LUN 0)
tssdcarda: tssdcarda1 tssdcarda2 tssdcarda3 tssdcarda4
ttts0 at MMIO 0x12400000 (irq = 33) is a TSUART
PHY: 0:01 - Link is Up - 100/Full
eth0: no IPv6 routers present
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
ep93xx-ohci ep93xx-ohci: created debug files
ep93xx-ohci ep93xx-ohci: OHCI controller state
ep93xx-ohci ep93xx-ohci: OHCI 1.0, NO legacy support registers
ep93xx-ohci ep93xx-ohci: control 0x083 HCFS=operational CBSR=3
ep93xx-ohci ep93xx-ohci: cmdstatus 0x00000 SOC=0
ep93xx-ohci ep93xx-ohci: intrstatus 0x00000004 SF
ep93xx-ohci ep93xx-ohci: intrenable 0x8000005a MIE RHSC UE RD WDH
ep93xx-ohci ep93xx-ohci: hcca frame #0005
ep93xx-ohci ep93xx-ohci: roothub.a 02001203 POTPGT=2 NOCP NPS NDP=3(3)
ep93xx-ohci ep93xx-ohci: roothub.b 00000000 PPCM=0000 DR=0000
ep93xx-ohci ep93xx-ohci: roothub.status 00008000 DRWE
ep93xx-ohci ep93xx-ohci: roothub.portstatus [0] 0x00000100 PPS
ep93xx-ohci ep93xx-ohci: roothub.portstatus [1] 0x00000100 PPS
ep93xx-ohci ep93xx-ohci: roothub.portstatus [2] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EP93xx OHCI
usb usb1: Manufacturer: Linux 2.6.29-ts ohci_hcd
usb usb1: SerialNumber: ep93xx
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usbcore: registered new interface driver zd1201
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0008
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS
CCS
hub 1-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS
PES CCS
usb 1-3: new full speed USB device using ep93xx-ohci and address 2
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS
PES CCS
usb 1-3: default language 0x0409
usb 1-3: New USB device found, idVendor=0ace, idProduct=1215
usb 1-3: New USB device strings: Mfr=16, Product=32, SerialNumber=0
usb 1-3: Product: USB2.0 WLAN
usb 1-3: Manufacturer: ZyDAS
usb 1-3: uevent
usb 1-3: usb_probe_device
usb 1-3: configuration #1 chosen from 1 choice
usb 1-3: adding 1-3:1.0 (config #1, interface 0)
usb 1-3:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0008
ts7000:~# uname -a
Linux ts7000 2.6.29-ts #4 PREEMPT Sun May 17 15:02:44 MST 2009 armv4tl GNU/Linux
ts7000:~#
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/ts-7000/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/ts-7000/join
(Yahoo! ID required)
<*> To change settings via email:
<*> To unsubscribe from this group, send an email to:
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
|