It worked for me on a 7260. Here is what I had that I think someone else posted before. On the newer 7260, they might install more of the modules by default.
insmod usbcore
insmod pcipool
insmod usb-ohci
insmod usb-ohci-ep93xx
insmod scsi_mod
insmod sd_mod
insmod /path/to/zd.o
ifconfig wlan0 up
iwconfig wlan0 essid wappy
ifconfig wlan0 192.168.0.99
ping 192.168.0.5
On 12/29/06, Tom <> wrote:
Hmm, I am still stuck. Anyone have any suggestions? I neglected to
mention that I'm using the included WIFI-G-USB option from
embeddedarm.com, an IOGear GWU-523. Has anyone else gotten this to work
with a TS-7260?
Tom
Tom McCarty wrote:
> Hi all, I just bought a TS-7260 a couple of days ago, and I can't get
> the wireless interface to work. The USB drivers seem to be working, but
> the iwconfig command doesn't seem to do anything, and I can't find
> anything in the archives with this particular problem.
>
> A full log of my interaction from bootup is included below, but I think
> the salient part is this, where iwconfig doesn't seem to do anything,
> and looks like it's reading from a corrupted data structure.
>
> $ iwconfig wlan0 essid pleasework
> $ iwconfig wlan0 mode ad-hoc
> $ ifconfig wlan0 192.168.0.2
> $ iwconfig
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> wlan0 \Â âxÂ*ÃÃ ESSID:off/any Nickname:""
> NWID:off/any Mode:Managed Frequency:2.412 GHz
> Access Point: FF:7F:B4:5C:AD:2A Bit Rate:1 Mb/s Tx-Power=off
> Sensitivity=2147482204/3
> Retry:off RTS thr=2432 B Fragment thr:off
> Encryption key:<too big>
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>
> I've tried "$iwconfig wlan0 nick test", too, but no iwconfig line seems
> to change the output of just "$iwconfig" except to specify the
> interface, in which case the output is slightly different:
> $ iwconfig wlan0
> wlan0 ââ ESSID:off/any Nickname:""
> NWID:off/any Mode:Managed Frequency:2.412 GHz
> Access Point: Not-Associated Bit Rate:1 Mb/s Tx-Power=off
> Sensitivity:0/3
> Retry:off RTS thr=2432 B Fragment thr:off
> Encryption key:<too big>
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>
> >From my as-shipped system, here's what I have done to it:
>
> uploaded zd.o to /root from ftp://ftp.embeddedarm.com/wireless/zd1211
> <ftp://ftp.embeddedarm.com/wireless/zd1211>
> uploaded iwconfig,iwlist, iwspy to /usr/bin from
> ftp://ftp.embeddedarm.com/wireless/wireless_tools
> <ftp://ftp.embeddedarm.com/wireless/wireless_tools>
> uploaded libiw.so.28 to /lib from
> ftp://ftp.embeddedarm.com/wireless/wireless_tools
> <ftp://ftp.embeddedarm.com/wireless/wireless_tools>
>
> I'm following the instructions in the Linux Arm guide v2.2, however, the
> zd.o at
> ftp://ftp.embeddedarm.com/ts-arm-linux-cd/binaries/ts-modules/zd.o
> <ftp://ftp.embeddedarm.com/ts-arm-linux-cd/binaries/ts-modules/zd.o
>
> is for ts10, and wouldn't work with my ts11 system, so I got a more
> recent version from another location on the web site. According to
> iwconfig --version, it should work, but obviously isn't. Anyone have
> suggestions?
>
> TIA,
>
> Tom
> -----
>
> Technologic Systems TS-LINUX/arm 7.0
> ts7200 login: root
> login[81]: root login on `ttyAM0'
>
> BusyBox v1.00-rc2 (2004.08.05-21:44+0000) Built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> $ insmod usbcore
> Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/usbcore.o
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> $ insmod pcipool
> Using /lib/modules/2.4.26-ts11/kernel/arch/arm/common/pcipool.o
> $ insmod usb-ohca
> insmod: usb-ohca.o: no module by that name found
> $ insmod usb-ohci
> Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci.o
> $ insmod usb-ohci-ep93xx
> Using /lib/modules/2.4.26-ts11/kernel/drivers/usb/host/usb-ohci-ep93xx.o
> usb-ohci.c: USB OHCI at membase 0xe0020000, IRQ 56
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 3 ports detected
> $ hub.c: new USB device not_pci-3, assigned address 2
> usb.c: USB device 2 (vend/prod 0xace/0x1211) is not claimed by any
> active driver
> .
> insmod scsi_mod
> Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/scsi_mod.o
> SCSI subsystem driver Revision: 1.00
> $ insmod sd_mod
> Using /lib/modules/2.4.26-ts11/kernel/drivers/scsi/sd_mod.o
> $ insmod zd.o
> Using zd.o
> zd1211 - http://zd1211.ath.cx/ <
http://zd1211.ath.cx/> - r83
> Based on www.zydas.com.tw driver version
2.5.0.0
> usb.c: registered new driver zd1211
> Release Ver = 4802
> EEPORM Ver = 4330
> PA type: 0
> AiroHa AL2230RF
> AllowedChannel = 000107ff
> Region:16
> $ ifconfig wlan0 up
> $ iwconfig wlan0 essid pleasework
> $ ifconfig wlan0 192.168.0.2
> $ iwconfig wlan0 mode ad-hoc
> $ iwconfig
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> wlan0 \Â âxÂ*ÃÃ ESSID:off/any Nickname:""
> NWID:off/any Mode:Managed Frequency:2.412 GHz
> Access Point: FF:7F:B4:5C:AD:2A Bit Rate:1 Mb/s Tx-Power=off
> Sensitivity=2147482204/3
> Retry:off RTS thr=2432 B Fragment thr:off
> Encryption key:<too big>
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
> $ iwconfig --version
> iwconfig Wireless-Tools version 28
> Compatible with Wireless Extension v11 to v20.
>
> Kernel Currently compiled with Wireless Extension v16.
>
> wlan0 Recommend Wireless Extension v13 or later,
> Currently compiled with Wireless Extension v18.
>
> $ iwconfig wlan0
> wlan0 ââ ESSID:off/any Nickname:""
> NWID:off/any Mode:Managed Frequency:2.412 GHz
> Access Point: Not-Associated Bit Rate:1 Mb/s Tx-Power=off
> Sensitivity:0/3
> Retry:off RTS thr=2432 B Fragment thr:off
> Encryption key:<too big>
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>
> $
>
>
-- Dr. Don W. Carr J. G. Montenegro 2258 Guadalajara, Mexico +52-333-630-0704 +52-333-836-4500 ext 2930
__._,_.___
![]()
SPONSORED LINKS
__,_._,___
|